Foundation: The foundation of a solder helping hand is very important. This Base will provide you with a foundational weight that will keep the elements in the hand, in place without moving them. The base foundation of the device needs to be heavy and sturdy enough that it does not move very easily. Also, please bear in the mind that the foundation board should also be broad enough to be able to hold the width of a good-sized PCB board apart from regular elements too.

Speaking of the clampers, they are strong and are small and also made out of stainless steel. They have a very strong grip to them and are attached to the 4 tentacles, which themselves are made out of sturdy industrial-grade rubber but very flexible too and can move about in 360 degrees. Aiding to the magnifying glass is a focus beamed LED light. This will further illuminate your project and aid in getting a highly detailed output. The magnifying glass is made out of high-quality impact-resistant glass whereas the LED lamp is powered by a battery. Accessories: Apart from the basics, a few of the solder helping hands also come with accessories that you might find interesting and quite helpful. For example, some boards come with an LED light that would illuminate your work and a few even come with a fan of sorts that would aid in faster cooldown of the solder etc., The base is heavy and weighted made out of solid stainless steel. It is powder-coated with industrial-grade rubber feet to make sure that the base does not move easily due to air or accidental hand fall.

address

Clamps: These refer to the tips that actually hold down the elements to be soldered. Most of the time, solder helping hands come with alligator clips but there are a wide different range of models too. A stainless steel clamp is always a wise choice.

Arms: The arms refer to the tentacle-like ornaments which would provide the height required to lift up the elements to be soldered. The thing that you need to remember at this juncture is that the hands need to be as flexible as possible and still need to retain enough sturdiness to hold the elements up in the air. Beaded tentacles are much preferred. A soldering helping hand is a nifty tool that aids in holding the circuit board and ensuring a proper solder joint. As the name suggests, they are a pair of mechanical hand-like clutches that hold together circuit boards, electronic components, or wires to facilitate an error-free joint creation. Great not only for DIY electronics but a wide range of works. All the elements in the product come with tight bolts that let you fix the stand to a single place. The entire set up would have a 10 inches width and 12 inches height thus perfect for a lot of projects. Furthermore, the manufacturer offers a lifetime warranty on this third hand to have peace of mind in its usage.The Chanseon soldering station is soldering helping hand with a very sturdy metal base and a hollow. The helping hand may not have a wide metal base but it comes with the great build quality and awesome accessories studded to it. Starting with it is the 3x zoom magnifying glass. This lets you inspect your project for greater detail and perform a better job. With a strong metal plate as its base, the tool has heavyweight to it and the bottom of the base has strong rubber feet to prevent slipping and it won’t tip over easily due to wind or any small accidents. The base is strong and has a great weight to it. It weighs about 2 lbs. to be precise and holds its own against any movement.

Even the alligator tip clamps that come with the device are strong and have a 360-degree rotation to them. Made out of solid weighted steel construction, the clips are durable and have a very strong grip on them. Starting off with the base, unlike conventional board bases, this Kotto soldering PCB holder has a pentagonal shape with 5 tentacles around on each side. All these tentacles surround converge along the center. Solder helping hands come with clippers that will hold the elements in place. All you need to do is adjust the height of the arms and place the two (or three) elements that need to be soldered together on the clips. Now you solder them together. Make sure that the solder is not touching the alligator clips Conclusion

7 Best Soldering Helping Hands Reviews

It has 2 pairs of anti-split rubber feet. This will keep the base in its place and not move about due to accidental touch or movement due to air as such. The feet are powder coated with industrial-grade rubber for no-slip. This 4-arm soldering helping hand is an ideal option for any soldering, painting, electronic, crafting, DIY work, or precision project where you need extreme accuracy. This ultimate workbench tool helps to clamp, hold and move the object to any position for smart and precise working. Great for a wide range of DIY applications, the stand comes with superior customer service and most importantly, a massive 3 months manufacturer’s warranty window too, which is a bit uncommon for soldering stations.