Keep an eye out for a blue and white striped pot that has a big red label on the front, with the name ‘Brasso’ on it. When you’re done using your Brasso you need to store it away in a safe place, that is out of the reach of children and pets.

Regularly wipe/buff the already treated areas with an additional clean cloth to see how you’re polishing exercise is going. Regularly wipe/buff the already treated surface with a new clean cloth to see how you’re polishing exercise is going. Brasso is abrasive and will wear metal over time. The National Trust recommend alternative cleaners. [7] Other applications [ edit ] Brasso has been used by watch enthusiasts to polish scratches out of acrylic crystals on watches. [12] Tip: If you’re using liquid Brasso, always pour the liquid from the can onto a clean cloth. Do not hold a cloth over the mouth of the can because this transfers dirt into the can. This then contaminates and weakens the Brasso inside the can. How to clean with wadding Brasso:

How Long Do You Leave Brasso on a Surface For?

Railway And Canal Commission." Times [London, England] 22 May 1913: 22. The Times Digital Archive. Web. 13 Sept. 2018. Brasso, if used correctly, will naturally be worked into a surface, and any residue will be buffed away by a clean cloth at the end of the exercise. If you buy a liquid can of Brasso, you need to pour a small amount of the can’s contents onto a clean cloth to use the solution. Always wear gloves and a mask– Brasso can cause skin irritation and inhaling the fumes may lead to drowsiness.

In addition to this, if you’ve used an appropriate amount of Brasso, and you’ve worked it into a surface and then buffed the surface again, you shouldn’t really have any excess Brasso left behind. So, you won’t need to ‘wipe Brasso off a surface’ per se. You’ve got to put some elbow grease into the cleaning exercise – it’s not just going to work on its own. Church, Roy A.; Andrew Godley (2003). The Emergence of Modern Marketing. Routledge. p.30. ISBN 0-7146-5390-X. Brasso is a metal polish designed to remove tarnish from brass, copper, chrome and stainless steel. It is available either directly as a liquid or as an impregnated wadding pad.

Can You Rinse Brasso Off with Water?

Continue to do this until the patch is clean – you might need to apply more pressure to certain grimey patches. You should remove Brasso from small nooks before it dries– Use a small, slim tool that’s wrapped in a cloth to tease the excess Brasso from crevices. Leaving the Brasso to dry will just make it harder to remove, and you might not end up with the sleek finish you were after if there’s Brasso residue all over the place.

Technically speaking, as you continuously massage Brasso into the surface you’re polishing, you will be wiping some of the product off as you go. This is what’s supposed to happen. Below you’ll find steps on how to use Brasso in both liquid and wadding form. Skip to the section that applies to the Brasso you’ve bought. General tips to think about before you start using Brasso: Gently rub a piece of Brasso wadding onto the surface you want to clean to perform a small patch test – make sure the Brasso doesn’t mark or stain the surface you’re about to polish. Using Brasso to clean and polish grotty metal surfaces is super easy, and doesn’t cost you a fortune! The online data sheet for Brasso wadding in the UK lists the ingredients as C8–10 Alkane/Cycloalkane/Aromatic Hydrocarbons, Quartz, C14–18 and C16–18 unsaturated Fatty acids, Kaolinite, Aqua, Ammonium Hydroxide and Iron Hydroxide. Brasso liquid lists a slightly different mix; C8–10 Alkane/Cycloalkane/Aromatic Hydrocarbons, Quartz, Kaolin, C12–20 Saturated and Unsaturated Monobasic Fatty Acids, Aqua and Ammonium Hydroxide. Also available are ingredients in a discontinued recipe for Brasso. Wadding: C8–10 Alkane/Cycloalkane/Aromatic Hydrocarbons, Quartz, Ammonium Tallate and Colorant. Liquid: C8–10 Alkane/Cycloalkane/Aromatic Hydrocarbons, Quartz, Kaolin and Ammonium Tallate. [6]Brasso, on account of its ammonia content, has been used as a de-coppering agent in rifle barrels to remove copper fouling. Brasso is a well-known metal polisher, that can be used to polish, remove tarnish and clean up chrome, stainless steel, copper, and of course, brass. Don’t leave a job half done – Once you start using Brasso to clean a surface, you should finish cleaning the surface in one go. If you leave the surface to dry, you’ll have Brasso residue. And as a consequence of this, items might not look shiny and evenly cleaned. The label of Australian Brasso lists "Liquid Hydrocarbons 630g/L; Ammonia 5g/L", whereas the material safety data sheet for Brasso in North America lists: isopropyl alcohol 3–5%, ammonia 5–10%, silica powder 15–20% and oxalic acid 0–3% as the ingredients. [4] However, the Australian version contains kaolin instead of silica for abrasives. [5]

Perform a small patch test to make sure the Brasso doesn’t mark or stain the surface you’re about to polish. If you’ve got some stubborn Brasso that needs to be cleaned away, follow these steps to get rid of the troubling Brasso: Although, if you’ve used an appropriate amount of Brasso for the surface you need to clean, and you’ve worked the Brasso into the item and buffed it as well, there shouldn’t be any need to remove the Brasso with water. Use small amounts of Brasso at a time, and add more product as you go– If you use too much Brasso you run the risk of it dripping everywhere as you use it, especially the liquid form, this is wasteful. It has been used to polish CDs, DVDs, screens, and pools to repair scratches. It is a mild solvent and an extremely fine abrasive, so when applied to the reflective surface of the disc and rubbed radially (in straight lines between the edge and centre), it can smooth scratches and reduce their effect. [8] [9] [10]If you do have Brasso residue leftover, either keep buffing it off the surface or use a clean cloth to remove it.