has been developed by Leon3D with the advice of Belloch laboratories with more than 50 years of experience in the manufacture of lacquers. In our experience, the the first time you use 3DLAC on your build surface apply two light coats (remember to shake the bottle before spraying). When making impressions 3-4 should be re-clean the motherboard 3DLac and re-lacquer spray again or liquid vaporizacor. Depending on the materials will be obtained different adhesions, so we advise before printing large parts with certain technical materials are pre-tested. is the perfect substitute for Kapton tape and other types of fixers due to cost-saving and its easy application.

The printing base should be allowed to cool down (at least to 30 ºC) before the part is removed from the printing bed. By accepting these services, we are able to show you videos or other media content hosted by external providers.A light 3DLAC mist over the surface is enough to hold completely the first layer of plastic to the base. A light 3DLAC mist over the surface is enough to completely hold the first layer of plastic to the base. spray is the best solution against warping by providing a great adhesion used filaments such as PLA, ABS, PETG and more materials. is constantly investigating how to improve the formula of the product to achieve greater adhesion to the base, hence the formula currently used is an improved version compared to the first.

This stick adhesive is easy to use and creates a strong bond between the build plate and the 3D printed part, reducing the risk of warping. Nylon printing presents unique challenges and opportunities, and we want to ensure you have everything needed for outstanding results. Once the printed piece gets cold, it can be taken off smoothly and without any damage to your 3D printed project. Prima, trading since 2014 are one of Europe's largest resellers and distributors of 3D Printers and associated products.

A product capable of fixing what was needed in each part of the printing process and which meets our conditions was essential. This facilitates application, allows for control over the amount of adhesive used, and a more precise and even distribution of the product on the printing base. P501 - Dispose of contents/container in accordance with local/regional/national/international regulations.

function is to hold the first layer of plastic so that it does not move at the start of printing, preventing unwanted failures in the early 3D printing process. Depending on the 3D printed material, the effect may vary, which is why it is highly recommended to test the 3DLac Stick with certain materials ( ABS, PP, Nylon or advanced polymers) before 3D printing the final part.All users who prefer use lacquer and not Kapton Tape, can be achieved with a sprayed or vaporized light on the glass bed base that the first plastic layer is fixed completely to this base bed. We pride ourselves in our commitment to bringing this fantastic technology to thousands of innovative new adopters, all with excellent service along your journey. On the one hand, there is the traditional spray lacquer version that allows the product to be easily and quickly expanded; and on the other hand, the new version in liquid vaporizer that allows to concentrate more the product and avoids that it is finished sticking it in the mechanical parts of the 3D printer as it usually happens with the 3DLac in spray due to a bad use of it. To use this product you only need to press the applicator against the printing surface for a couple of seconds and once the adhesive flows, it spreads a light layer of product over the printing area.

You can read all about the cookies we use, how they work and how you can adjust your preferences in our Cookie Policy. The 3DLac Stick adhesive dries quickly, lasts very long and is compatible with multiple materials and 3D printing surfaces. After your print is ready, we recommend that you let the print bed cool down before removing your 3D printed object from the bed. PrinterMods is a proud cog in that machine - supplying the maker community with what they need to grow and thrive.

We started printing right back in 2014 and have tried every trick in the book when it comes to bed adhesion. If you choose to decline, then we will only use functional and analytical cookies and you will continue to see random advertisements. ensures that the first layer of each 3D print adheres securely to the build plate surface, making sure the print starts well and stays in position.