Windows-systemen met een verouderd BIOS die Extended Capacity Managergebruiken, hebben twee partities nodig op de opstartschijf om de volledige capaciteit te benutten.

If the drive is detected properly, add the disconnected devices one by one until you find the one that is causing the problem. Open the computer case and remove the data cable from the hard drive. This will stop any power saving commands from being sent. Noises can be caused by mounting issues. This is due to either a high-frequency vibration in the mounting hardware or a potential drive failure. Please remember that these third-party programs do not have proprietary access to Seagate hard disk information, and therefore often provide inconsistent and inaccurate results. SeaTools is more consistent and more accurate and is the standard Seagate uses to determine hard drive failure. If your motherboard only supports SATA1 (1.5 Gbits/sec transfer rate) and you are installing a SATA2 (3.0 Gbits/sec) or SATA3 (6.0 Gbits/sec) drive, the motherboard may not detect the drive. There are four options in that case:Vereisten voor systeemgeheugen: 1 GB en hoger voor 32-bits systemen; 2 GB en hoger voor 64-bits systemen. Confirm you are using the current SATA driver from the manufacturer of your SATA motherboard/controller. Once you connect a new Serial ATA drive in your computer, there remains more to do to get your drive working. Het opstartproces is vertraagd op een computer waarin een grote harde schijf is geïnstalleerd en waarop Windows 7 of Windows Server 2008 R2 draait

After you install a device or update a driver for a device, Windows Vista or Windows 7 may not start

Kies uw SSD

Switch power cables with a device like a CDROM or DVDROM drive so that you are using a known-good power cable. This set of troubleshooting steps will attempt to get the drive detected again, or to conclude whether the drive has failed and should be replaced.

Generally, if a SATA drive is configured as the bootable drive, then the computer relies on that drive to boot the computer and to launch Windows. It is the source of most of the computer's operations. So, if the computer suddenly stops detecting the bootable drive, this will almost certainly mean that the computer will fail to boot at all. Instead, some error message will occur, and it will become obvious that a serious problem has occurred. Connect to an External Enclosure (Please verify if the enclosure is compatible with the hard drive). If you are simply going to install a new copy of Windows (the operating system), you first need to format and partition the drive, and then install Windows: Windows Vista en nieuwerNative ondersteuning voor niet-opstartschijven van 3 TB vindt plaats met GPT-partities, wat beschikbaar is op alle systemen. First, please see Document ID: 196169 for more information on installing drives and Document ID: 188411 about the proper drivers in Windows (though if your computer's boot drive is SATA, there should be no need for additional drivers).

The simplest way to reinstall the operating system (and probably erase the data, though that does not happen every time) is to insert the Windows CD/DVD in the CD/DVD drive and then reboot the computer. The option to repair Windows should appear as well as an option to reinstall Windows. Since the repair has failed, simply choose to reinstall Windows. Windows Vista en nieuwerNative ondersteuning voor opstartschijven van 3 TB is alleen op UEFI BIOS-systemen en met gebruik van GPT-partities. If a Serial ATA drive, installed as additional storage in your computer, was previously detected but is no longer detected, this set of troubleshooting steps will attempt to get the drive detected again, or to conclude whether the drive has failed and should be replaced.

I am attempting a new installation of a bootable Serial ATA drive in my PC and it is not detected correctly Disconnect all external storage devices such as USB, Firewire, and eSATA drives, jump/thumb/flash drives, cameras, and printers before proceeding with a Windows repair or recovery. Failure to disconnect such devices could result in serious data corruption. Extended Capacity ManagerDe software installeert een apparaatstuurprogramma om de volledige capaciteit te kunnen benutten op verouderde BIOS-systemen.See also Document ID: 196169 for more information on installing drives and Document ID: 188411 about the proper drivers in Windows. Before the drive can display in (My) Computer/This (PC) or Windows/File Explorer, it must be formatted in Windows. Please see the following articles for instructions: If the drive is detected there and the colored bar to the right is still dark blue (see figure), follow the steps to Reset the Drive Letter . Disconnect all external storage devices such as external USB, Firewire, and eSATA drives, jump/thumb/flash drives, cameras, and printers before proceeding with a Windows repair or recovery. Failure to disconnect such devices could result in serious data corruption. Once you connect a new Serial ATA drive in your computer as additional storage, there remains more to do to get your drive working.