Seal that shower – Follow our shower tray sealing tips above for hassle-free shower sealing with a smooth, neat finish. Room H2O appreciates that DIY is not everyone’s cup of tea and there are some jobs you would rather leave to the professionals.

Use gentle pressure to the trigger of the application gun and work towards the front of the shower tray in one continuous, smooth action to ensure application of a uniform silicone bead. Thoroughly dry the shower tray area with paper towel or allow the shower tray to air dry for a couple of hours before applying the silicone sealant, which will not adhere properly should any moisture remain. Remove old sealant – Use a sealant remover to dissolve the existing sealant, or, carefully scrape at it with a plastic or metal blade.While this is suitable for use with silicone sealant and caulking, similar good quality tools can be purchased from tile retailers and good DIY outlets. Once a smooth, uniform bead has been achieved around the shower tray, do not be tempted to keep smoothing the silicone as it will start to tear, look untidy and may not adhere correctly. This section has hundreds of instructional videos showing how to do the easiest of DIY related jobs right up to a full bathroom refurbishment. A sharp knife will be required for opening the silicone sealant and trimming the application nozzle to size.

It should specify that it is suitable for use in bathrooms / wetrooms and contain an anti-mould and bacterial additives such as Kerakoll Fugabella Eco Silicone Sealant or Kerakoll Fugabella AM Silicone Sealant, which are both available from our sister company UK Tiles Direct. The Fugi, produced by Cramer (pictured below), features cut outs of various sizes which produce different bead thicknesses. Give the area a final wipe down with a clean damp cloth to remove any residual detergent but do not get the area wet. Starting from the point the silicone was first applied, place the silicone sealant smoothing tool against the shower tray and tiles.Here are some handy tips to set you on the right path and make sure you apply silicone sealant correctly to achieve a professional finish and prevent water leaks. Choose the correct type of silicone sealant that is compatible with your chosen wall or floor coverings (such as natural stone, porcelain tiles or ceramic tiles). We know that not everyone has the luxury of a freestanding bath and that many modern bathroom designs will incorporate over-bath showers that also require sealing. Wondering how to seal a shower tray or looking for top DIY tips on how best to apply silicone sealant? One of the most common causes of water leaks from shower trays, shower enclosures and baths is the poor application of silicone sealant.

Should you require more information about our shower sealing and bathroom fitting services, do not hesitate to get in touch. If you cannot find the information that you require please leave a post in the DIY Forum as one of the many Forum members may be able to help. When sealing a bath, follow the preparation advice above but remember that there is one crucial extra step you will need to take before reaching for the silicone sealant. Check the shower tray and walls are completely dry and free from dirt, dust, grease and debris or the silicone sealant will not adhere correctly.

The nozzle of the silicone sealant tube will usually feature perforated marks to indicate where and how to trim the nozzle but a good rule of thumb is to cut at a 45-degree angle and create a 5-6mm hole in the end of the tube, which can be enlarged if a wider bead is required.

Made from rubber and designed to remove excess sealant, these handy tools will help you achieve a neat bead of silicone when sealing a shower tray. This is often the only solution to get a waterproof seal, if the gap between the tiles and the shower tray is too large.Usually, fresh silicone should be left to dry or cure for a minimum of 24 hours, although this depends on the brand and type of sealant. Follow the manufacturer’s instructions – As a rule of thumb shower doors and enclosures should only be sealed around the outside at the bases and on the inside and outside of the vertical profiles where they meet the tiled walls. Clean and dry – Use warm water containing a mild detergent to thoroughly remove grime and residue from the area and then use paper towels or a hairdryer to speed up the drying process. With that in mind, we offer a full range of specialist services from bathroom installation services in Dorset to made to measure shower enclosure survey and installation services throughout the South East. Ensure the bead of silicone sealant is continuous and thick enough to fully cover the gap between the shower tray and the tiles.