Plasterboard is quite soft and the slightest of impacts such as when moving furniture can mark the surface and even put a hole right through it. The same can also be said for hollow doors – Due to the void in the centre and MDF or fibreboard used as the covering, this does not provide much protection when it comes to resisting impacts. Finally, always follow the paint manufacturer’s recommendation, apply a primer or sealer before decorating. Gyproc EasiFill 45 is also available in handy 1kg sachets in our Gyproc EasiFill 5×1 boxes, perfect for smaller jobs like application of plasterboard patches.

Now you will need a piece of plasterboard to fill the hole. Ideally this needs to be thinner than the current plasterboard. Measure and cut to fill the hole. Fix in place against the noggins with plasterboard screws or nails. Another way to fill a hole in plasterboard is to enlarge the hole first to make a square of a suitable size. Then cut two battens (19 x 38mm timber will suffice) and make sure they are 100mm longer than the size of the square you have cut. Gyproc EasiFill 20 has a working time of 20 minutes and the second coat can be applied after 40 minutes. Gyproc EasiFill 45 has a working time of 45 minutes and the second coat can be applied after 80 minutes. Cut a piece of plasterboard that is slightly narrower than the hole but an inch or so longer top and bottom. Screw in a long screw in the middle of the patch; this will be used to position the patch in place.

Credit limit exceeded

Caulk can’t really be sanded down so you need to get it as smooth as possible. For any larger holes you are much better served by a more suitable filler. How Do You Fill Screw Holes In Plasterboard? This method is very similar to fixing holes in plasterboard on walls. If it’s a small screw hole or nail hole just use a putty knife and a suitable filler, and smooth out. Rub down when finished. To repair a hole in a hollow door, wall, or ceiling, firstly trim the edges of the hole and make is square. Ironically, you actually have to make the hole larger before you can go about fixing it! As you will need to do a bit of cutting, before you start this, firstly run over the area around the hole with a wire detector to make sure there aren’t any wires, pipes or other items that you may accidentally cut through.

Remove any loose bits from the edge of the hole or damaged area, and sand this down. Remember to always wear eye protection when sanding. Yes you can use decorators' caulk to fill small holes such as nail and screw holes, but it's not really suitable for holes any bigger than quarter of an inch. Add a dollop of caulk and smooth out with a putty knife or a wet finger for nail and screw holes. Apply the filler by working it into the holes of the patch and towards the edge. Feather out at least 50mm beyond the edges of the patch to create a smooth, seamless finish. Leave to set for a minimum 30 minutes.

Add as much filler as you need to until the hole is filled flush with the surface of the wall. Use the trowel to get the surface as flat as possible. Once the Gyproc EasiFill is fully dry, you may see darker patches – this is where the product is chemically set before it air dries. Once painted, these will completely disappear. It’s always good to finish by giving the entire area a light sand for a perfectly, smooth finish. Depending on the shape of the hole, whether its circular or has jagged edges you may need to use a padsaw, jabsaw or hobby knife. Be careful using any of these items as they are sharp and can slip quite easily. Artex Caulker (250mm ) helps to fill joints and create smooth finishes or any suitable jointing knife

Time saving and mess free compared to traditional methods of filing a hole with newspaper and building up layers with filing compound Once the patch is dry and firmly in position, gently remove the screw. Use patching plaster, all purpose filler or multi-finish plaster — mix up enough to cover the patch and gently press into the hole and spread with a putty knife that is larger than the hole to help get a smooth finish. Picture the scenario. You have a job list as long as your arm, but you’re seeking efficient solutions for your customers, saving you time but not cutting corners. Once dry, you can gently rub down the plaster or filler, and then paint the repaired area to match the surrounding wall. How to Fill Large Holes in PlasterboardFor larger holes locate the joists either side of the hole in the ceiling and mark the middle with a straight pencil line and create a rectangle around the hole. Cut out and add two noggins to bridge the gap between the joists. Another complication that springs to light when you have unfortunately made a hole in a plasterboard wall or hollow door is the void behind it due to the construction of the stud work used to hold the plasterboard up or provide the framework for the door meaning that you can’t just use filler as there is nothing to bond it to. Spread a small blob over the hole and wait for it to dry. Once dry, get a 180-220 grit sandpaper and rub down until smooth and blended with the current surface. How do You Fix a Hole in Plasterboard on the Ceiling? The first thing to do is to cut out a rectangle around the hole using a steel rule and a Stanley knife. Alternatively, mark out with a pencil and ruler and cut out with a jab saw. Now you need to measure and cut two noggins (horizontal wood that bridges the gap between the studs). Use a bit of 2 x 4 inch – approximately 100mm x 50mm – timber to create the noggins. Nail or screw them into position, between the studs, from the sides. This will create an area to fix your new plasterboard patch to.

Now draw two lines across the gap to create a rectangle around the hole. Cut out the existing plasterboard with a sharp Stanley knife or use a small jab saw.Read on to find out how to repair holes in plasterboard with the Gyproc EasiPatch Plasterboard Patch. Now that you have squared up the hole, the next job is to make a patch. You can either use a scrap piece of plasterboard or timber. Once the first coat has set if you find any ridges, lumps, bumps or trowel marks, gently scrape these away using the edge of your filling knife, or leave to fully dry before sanding. Measure and cut a new piece of plasterboard to fill the hole. Fix in place with plasterboard screws or nails. Mix up plaster, apply and leave to dry. Use a digital stud detector to locate studs, noggins and joists in walls and ceiling (Image credit: Getty Images) Can I Use Caulk To Fill Holes?