Remove the two jumpers from CN2, and place them at the two outermost empty jumper pins marked CN11 and CN12. Add commands ``ChannelRemap``, ``MultiPWM``, ``AlexaCTRange``, ``PowerOnFade``, ``PWMCT``, ``WhiteBlend``, ``VirtualCT`` as synonyms for ``SetOption37, 68, 82, 91, 92, 105 and 106`` respectively Microchip'sLAN8720A/LAN8720Aiarehigh-performance, small-footprint, low-power 10BASE-T/100BASE-TX transceivers specifically designed for today's consumer electronics, industrial and enterprise applications. The LAN8720A/LAN8720Aiare the industry's smallest footprint solutions with up to 40% lower power consumption than existing Microchip transceivers. The LAN8720A/LAN8720Ai have an integrated voltage regulator and ESD protection components to help reduce Bill of Material (BOM) costs.

TheLAN8720A/LAN8720Ai connect via an RMII interface.These devices support HP Auto-MDIX†, employ Microchip's proprietary flexPWR ® technology andare available in both extended commercial (0°C to 85°C) and industrial (-40°C to 85°C) temperature range options. iBeacon (xdrv_52): Clean up BLE_ESP32 based driver; add commands and advert timing. Remove HM10 code - it's in the other one.....EDIT: After reading that the lenght of wires can be an issue at 50MHz, I wired it with 10cm wires (instead of 20cm on the photo), still the same. In the future, Ethernet support using external PHYs will change significantly and support may change. When STM become officially supports external PHY Ethernet, I will delete this repository. Hardware requirements

Actually the board has two STM32 chips. One is the target of the demo board, and the other is the STLINK.EMAC_TXD0, EMAC_TXD1, EMAC_TX_EN, EMAC_RXD0, EMAC_RXD1, EMAC_RX_DV and EMAC_TX_CLK are fixed and can't be rerouted to other GPIOs. Pin# of the enable signal for the external crystal oscillator (-1 to disable for internal APLL source) Go grab your Raspberry Pi Pico board and a micro USB cable. Plug the cable into your Raspberry Pi or laptop, then press and hold the BOOTSEL button on your Pico while you plug the other end of the micro USB cable into the board. Then release the button after the board is plugged in. Example configuration entry ethernet : type : LAN8720 mdc_pin : GPIO23 mdio_pin : GPIO18 clk_mode : GPIO0_IN phy_addr : 0 # Optional manual IP manual_ip : static_ip : 10.0.0.42 gateway : 10.0.0.1 subnet : 255.255.255.0 Configuration variables: ¶

Espressif have published some code for the TLK110. But it is relatively expensive (around 6 EUR when bought in small quantities) and is relatively big as it has an MII-interface which is not entirely needed. my knowledge is not so deep to understand if Olimex has more feature than the proposed cheaper device HP Auto-MDIX eliminates the need for special "crossover" cables when connecting LAN devices together. BLE_ESP32 (xdrv_79): Start scan as soon as we are connected to a device - saves missing a few adverts.

I have copy and pasted template {"NAME":"WT32-ETH01","GPIO":[1,1,1,1,1,1,0,0,1,0,1,1,3840,576,5600,0,0,0,0,5568,0,0,0,0,0,0,0,0,1,1,0,1,1,0,0,1],"FLAG":0,"BASE":1} The LAN8710A/LAN8710Ai connect to the MAC layer using a variable voltage, digital standard MII or RMII interface,These devices support HP Auto-MDIX†, employ Microchip's proprietary flexPWR ® technology andare available in both extended commercial (0°C to 85°C) and industrial (-40°C to 85°C) temperature range options. I made a small prototype for the eBox ESP32-T and the Waveshare LAN8720 ETH Board which already has an 50MHz oscillator. emac: Timed out waiting for PHY register 0x2 to have value 0x0007 (mask 0xffff). Current value 0xffff emac: Timed out waiting for PHY register 0x3 to have value 0xc0f0 (mask 0xfff0). Current value 0xffff