Where the existing coating is defective it must be completely removed and the surface prepared as described for new or bare wood above. Sand the surface in the direction of the grain to remove any imperfections etc. and remove residues with a damp lint free cloth.

Do not apply Dulux Trade Diamond Glaze in temperatures of 10°C or lower or in areas of high humidity or condensation. Hours - This will vary according to temperature and humidity and will take significantly longer in cold, damp conditions.New or bare wood: Sand the surface in the direction of the grain to remove any imperfections etc. and remove residues with a damp lint free cloth. Seal all new or bare wood by applying one coat of Clear Gloss Diamond Glaze, to help reduce variations in absorbency which can lead to differences in colour and sheen, particularly when working with coloured topcoats of Diamond Glaze. We recommend always follow the manufacturer's instructions found on the tin. Stir thoroughly, it is recommended that a small test area is applied before treating the entire surface to ensure compatibility. We also deliver to the majority of non mainland UK locations including The scottish Highlands & islands, Isle of Man, Isle of Wight, Isles of Scilly and Northern Ireland. Please see full delivery terms for the extra charges associated with these locations

Apply 2 or 3 coats evenly and consistently, taking care to keep the 'wet edge' alive and finish off along the grain. Before using coloured Diamond Glaze Varnish on base wood, pre-seal with a coat of Diamond Glaze Varnish Clear Gloss to minimise colour absorption differences. I am sorry to hear that your project did not turn out as expected, I suspect this may be due to the high oil content in dense hardwoods such as Iroko. Coated surfaces in poor condition: Where the existing coating is defective it must be completely removed and the surface prepared as described for new or bare wood above. We will be happy to organise an exchange for the correct goods at no extra charge to yourself, please get in touch to organise this. Faulty Items

Pallet agreements which are about to expire

Rub down the thoroughly cleaned surface with 120 grit abrasive, vacuum and leave to settle overnight. Remove dust from the surface with a damp cloth and allow to dry. Prime the surface with one coat of Diamond Glaze Clear Gloss. Leave overnight to dry then lightly sand with the grain using 120 grit abrasive and remove dust before finishing with a further 2-3 coats. All traces of grease, wax and polish must be completely removed prior to applying Diamond Glaze Varnish Seal all new or bare wood by applying one coat of Clear Gloss Diamond Glaze Varnish to help reduce absorbency variations, which can cause differences in colour and sheen. Wood dyes may be used prior to applying Diamond Glaze Varnish. It is recommended that a water- based dye be used. After cleaning or stripping a test area, place a drop of water on the bare wood - if it forms a bead, wax is still present and Diamond Glaze should not be used without thorough preparation. If the water disperses, carry out the application/adhesion tests above before proceeding with cleaning, stripping and priming.

Wood stains or dyes may be used prior to applying Dulux Diamond Glaze Varnish. It is recommended that a water-based stain be used Make sure surfaces to be varnished are sound, clean and dry. Special precautions should be taken during surface preparation of pre-1960s paint surfaces over wood and metal as they may contain harmful lead. Light foot traffic is allowed after 24 hours but to prevent possible damage to floor while the full mechanical resistance develops, avoid heavy wear and do not replace carpet or rugs or move furniture for at least 7 days after application. Diamond Glaze is up to ten times tougher than conventional varnish and is resistant to common chemicals, alcohol and water. Suitable for use over materials such as cork tiles, hardwood and chipboards. Stir thoroughly before you begin, taking care not to use a whipping motion, which will introduce air and cause foaming when applied.

Diamond Glaze

New or bare wood: Sand the surface in the direction of the grain to remove any imperfections etc and remove residues with a damp lint free cloth. Surfaces should be protected from water, steam, spillages and hard stress, for example abrasion or polishing, for a minimum of 5 days after application. After degreasing the wood, we often recommend application of very thin oils such as Osmo Wood Wax Finish Extra Thin 1101 which are especially designed for wood types such as iroko to penetrate into the grain and protect the wood without adhesion issues. Test areas also help ascertain the absorption of the product. A. Diamond Glaze is known for its exceptional durability and resistance to wear and tear. It provides a tough, protective coating that helps to extend the lifespan of the surfaces it is applied to. This makes it particularly suitable for high-traffic areas or surfaces that are prone to frequent use and abrasion. The varnish has excellent scratch and stain resistance properties, making it ideal for surfaces that require added protection. It helps to prevent scratches, scuffs, and stains, which can be particularly beneficial for wooden floors, furniture, and other surfaces that are susceptible to damage. Floor Sanding: To achieve an even appearance, prepare the floor by using an industrial drum sander and edge sander (available from a local hire shop). Always sand in the direction of the grain. A belt sander or orbital sander can be used for smaller areas. Remove all dust from floor and surrounding areas using suitable vacuum equipment.

Special precautions should be taken during surface preparation of pre-1960's paint surfaces over wood and metal as they may contain harmful lead. Test a small clean area first, sand with 120 grit abrasive and dust off. Apply a test patch of Diamond Glaze - if the Glaze leaves uncoated spots, the surface is contaminated and needs to be stripped. If the film formed is unblemished, leave for 24 hours then test for adhesion by scraping with a coin. If the surface is sound, continue with preparation and priming as described above. Special precautions should be taken during surface preparation of pre-1970s painted surfaces as they may contain harmful lead Floor Sanding: For even appearance, prepare the floor by using an industrial drum sander and edge sander, available from a local hire shop. Always sand in the direction of the grain. A belt sander or orbital sander can be used for smaller areas. Remove all dust from floor and surrounding areas using suitable vacuum equipment. General: All traces of grease, wax and polish must be completely removed. See Diamond Glaze Varnish from Dulux Trade leaflets for further information. Diamond Glaze Varnish is not suitable for use on laminated floors.New or bare wood should be sanded in the direction of the wood grain to remove any surface imperfections To get the best results, ensure surfaces to be varnished are sound, clean and dry. Special precautions should be taken during surface preparation of pre-1960s paint surfaces over wood and metal as they may contain harmful lead. Seal new or bare wood by applying one coat of Diamond Glaze Clear Varnish to help reduce variations in absorbency, which can lead to differences in colour and sheen