If you do get some epoxy onto your skin, the best thing is to act fast. You can either use a cloth dipped into some vinegar and placed over the area or some acetone on the tip of an earbud. Rub onto the adhesive until it comes off. A tip when using epoxy putty, keep your gloves moistened, this will help to make it easier on application and creates a smoother look.

Both waterproof pipe repair tape and plastic repair epoxy putty will provide you with a long-lasting soil pipe repair. You can reinforce the seal provided by either of those materials with a pipe repair bandage wrapped over the top. Use the spreader to mix the Putty and Hardener to a ratio of approx a 30mm (3cm) line of Hardener, to approx a 40mm (4cm) diameter ball of Putty (golf ball size). (This is a ratio of approximately 3-4% hardener to 96-97% Putty). Mix until you have a consistent colour. Try not to create air bubbles when mixing the two components. (Once mixed the Putty will start to harden within a few minutes so we advise you only make up an amount that can be applied within this workable timescale). You should choose the size that best suits your needs, do you need adhesive for a small or larger area. Some adhesives come in a one-time-use container, which is great for smaller projects. However, you will need a larger amount for bigger projects, so make sure you work this out before you go out and buy.

Yes, epoxy adhesive offers many benefits including heat-resistance, chemical resistance as well as water resistance. Great to use on those plastic plumbing problems. As you wrap the tape around the damaged area of pipe, it will bond to both the soil pipe and itself to form a solid rubber band over the leak area. This band provides a high pressure repair; multiple tapes when used together can hold up to 30bar. Epoxy falls under the reactive adhesives, as it goes through a chemical reaction and then hardens or cures. Epoxy usually consists out of two-parts, the epoxy, and a hardener, which when combined forms a tough layer. Super glue is also a reactive adhesive and can be described as a one-part adhesive, which reacts to environmental conditions like heat. The popular white glue is an example of a non-reactive form of adhesive.

You are now ready to prime the repaired area. We recommend the E-TECH Technik Repaired Surface Primer, Part No ER00109; follow the instructions on the can. Whenever you are dealing with adhesives, you will need to match it with the material you are working on. Here are a few examples:Stay safe. Work in a well-ventilated, protected area. Wash your hands when you are finished, and optionally wear gloves for extra protection. Whilst epoxy putties will bond to virtually any material, one which has been formulated for plastic repair will come with plastic running through it, offering a tailored repair. It will also cure to white, blending in seamlessly with your PVC soil pipe. Feather Edge – Sand the edge of a paint layer so it tapers down to the metal/plastic surface leaving no ridge or edge

When dealing with epoxy that has hardened may be difficult but not impossible. You will first have to soften the epoxy with an adhesive remover. You can also try denatured alcohol or paint thinners. Take a cloth that has been dipped into the remover and wipe the affected area. You should be able to remove the resin without leaving any residue, especially if you have used the correct adhesive remover. Always work in a ventilated space and wear gloves to avoid getting onto your skin. The best epoxy for plastic is the more durable option when it comes to adhesives, as it can withstand temperatures, UV light, solvents, and can endure a measure of force. We can now move on to some pros and cons of using a two-part epoxy adhesive. Allow the Putty to fully cure/harden for approx 30 minutes at room temperature. It may take longer to cure in cooler temperatures or if the correct ratio of Putty to hardener is not exact. If you do want to reinforce your repair, then consider buying a pipe repair kit as opposed to individual items. Kits come with both the sealing material and a bandage at a cheaper cost than when buying items individually. When the epoxy is still soft, it should be easier to remove. Take and use some acetone, which should help. Using a cloth with the acetone, wipe the area with the glue and it should eventually lift off.Prepare surfaces. Surfaces should be close fitting (pre-fit before joining), free of residue, and dry. Slightly roughen smooth surfaces to improve results.