Solder a 3-pin header to the 'E# STEP DIR EN' vias and connect the external driver. ¶ Physical connections ¶ Wiring diagram • Revision 0.11 The VFAN voltage can be selected by a jumper as VIN, 12V (internally generated) or 5V. ONLY ONE JUMPER SHOULD BE FITTED. Using more than one jumper could cause permanent damage to the DueX2/5 and/or the Duet 2. If you power up the Duet before you power up the DueX, the stepper drivers on the DueX won't get initialised. Ideally power them up at the same time, or the DueX first. For these revisions the DueX2 had only the first two stepper and heater channels populated, only 2 fan, heater and temperature channels populated, and only the first 3 servo channels are enabled (although all 5 headers may be populated). • 0.8

With USB-C connectivity, Duex Plus delivers additional screen space for your Android* phone. In addition to providing a more comfortable view of any content, this larger scale is perfect for complex tasks such as editing documents, photos, and video. To break the circuit to make the DueX5 appear to be a DueX2, gently remove the copper ring of the jumper using a 1mm drill bit and confirm its removal by testing between the two pads using a multi-meter; there should be no connection.

Giuliano Moschini has created a model based on the Duet 2 WiFi model for the Duet 2 Ethernet available here ¶ Physical connections ¶ Wiring diagram ¶ Revision v1.0 and later If everything is working so far, apply 12V or 24V power and proceed with testing other devices you have connected. A second screen attached to your laptop makes plenty of sense if you spend lots of time away from your home or office, for instance, or if you just don’t have the space to use a second monitor. Pricing and availability The choice to exclude an HDMI port is fine because the DUEX Max may then use a single cable for both power and data. Mobile Pixels does consider that you may be limited to USB-A 3.0 plugs on your notebook, which makes the DUEX Max truly plug and play. While the display itself doesn't push the boundaries, the inclusion of the G-Sensor is a nice, useful touch. On top of that, being able to use it in portrait mode could also be useful in stationary desktop environments. Being a portable screen, you may use it with mobile devices capable of piping out video, like the Nintendo Switch. However, in that case, you will also have to find a separate power source for the second port. Note: (There is an error on v1.0 and v1.01 on the silkscreen where the E0-/E1- and VIN are reversed - use the diagram above rather than the silkscreen. This is fixed in v1.02 boards)

The PWM channels for servos or other uses are shared with the heaters. DO NOT HAVE A HEATER PLUGGED INTO A CHANNEL YOU CONFIGURE PWM. Doing so will cause the heater to heat in an uncontrolled manner and potentially cause a fire.We’re an online magazine dedicated to covering the best in international product design. We have a passion for the new, innovative, unique and undiscovered. With our eyes firmly focused on the future. Selects voltage for PWM fans, between 5V (internally or externally supplied), 12V internal and VIN. On top of that, thanks to the housing, you may simply stand the DUEX Max upright in portrait mode. Funnily enough, this scenario immediately felt like it has a lot of potential as that second screen in a more stationary setup; say, your home office or permanent desktop. The G-Sensor does not trigger for this state, so you have to manually set the screen up within the host operating system. Both Duex® 868 and standard Duex® can also be supplied in a lighter 6/5/6 configuration, however IAE would always recommend using heavier 8/6/8 panels in a sporting environment. The slightly bigger screen size means it’ll fit bigger laptops. However, if you plan it for a smaller laptop, do note that the low clearance area at the bottom may limit your ability to tilt the screen down.

Split the 5V rail into 5V_INT and 5V_EXT. this provides additional protection to some of the more sensitive components on the board from abuse in the form or feeding >5V into a 5V pin. STP pins are 8V-tolerant on revision 1.04 and later, Z Probe IN pin is 30V-tolerant in revision 1.04 and later The boards all support connection to a computer over USB, using any standard 3D printer host control program. The Duet 2 WiFi can also connect to a secure WiFi network, while the Duet 2 Ethernet has an Ethernet port. The primary way to control these boards is with a web interface controlled through the network. Although they have removable on-board SD cards, the network interfaces provide fast enough file transfer that it is generally preferable never to remove the on-board SD card. For the initial beta testers who have the old WHITE pre-production boards the pin out is below. The differences from the production boards are:

Use the supplied 50-pin ribbon cable to connect the DueX2/5 expansion connector to the host Duet 2 WiFi/Ethernet expansion connector. Like its counterpart above, the Trio Max monitor is a versatile device and can rotate and swivel. It’s compatible with both Windows and macOS operating systems. And guess what? You can use it as an external monitor for your Nintendo Switch (see best Nintendo Switch cases). Cool, right? If you have connected additional thermistors, thermocouples or PT100 sensors, send appropriate GCode commands to enable them and test that they are giving the correct readings. In some cases, where current draw is particularly high, for example you have a large number of heaters, you may want to connect more than one PSU.