House Roof - Another split system, 1 x South & East and 1 x West each using a Solis S6 Inverter (installed 2022).

I noticed that the Frient I bought came with a read head called “LED”. The documentation mentions other supported head types. I would imagine that this head can only read light pulses. My assumption is that there is nothing stopping the end-user from replacing the head with an IR read head and setting the interface mode to IEC62056-21. The new drivers allow you to activate and deactivate the sirens of the Intelligent Smoke Alarm, the Intelligent Heat Alarm, and the Water Leak Detector in the Homey app. Use this to set up a flow that if one alarm detects a fire or water leak, all alarms will turn on their sirens for a specific amount of time, and you’ll have all alarms interconnected. Det er ikke længe siden jeg sidst skrev et indlæg om hvordan indblik kan nedbringe vores elregning, og nu kommer der endnu et indlæg om emnet. Vores strømregning er nemlig steget ca. 100% siden januar, så problemet får lidt mere fokus. People who want to see how much energy they're using and who want to make small, positive changes to their energy usage could benefit from an energy monitor. Combining them with a cheaper energy deal can help to save even more. However, I am having the same issue as above where there is no unit of measurement and I cannot use it with the home assistant energy electricity grid set up.

Smart Siren now works with Homey

frient Electricity Meter Interface 2, wireless meter readings, energy consumption monitoring, interface for electricity meters with LED pulses, Zigbee, works with Homey and SmartThings Men hvad hvis man gerne vil vide hvor mange watt hele husstanden bruger her og nu? Eller hvor mange kWh som der er forbrugt den seneste time eller døgn? The Frient can identify energy peaks in your home and enable you to start moving some of your consumption to off-peak periods. The Electricity Meter Interface 2 cannot be used in installations with power production such as PV systems or similar. I do not like to rely on cloud systems and prefer to keep my data local, I also like to have several different ways to collect my solar data in case 1 stops working for a period.

Many homes still have no smart meter at all - the government's current goal is to have suppliers install the devices in at least 85% of homes by 2025. An energy monitor provides a way for those without a smart meter to keep an eye on their energy usage. Den nemmeste måde at måle samlet strømforbrug, er at måle det hvor det hele kommer ind – nemlig ved elmåleren.sensor.electricity_meter_smartenergy_metering_summation_delivered seems to be showing a constantly incrementing value that is now at 1451.0. Is this the total kWh I have used? More likely I guess it is Wh and I would need to create a template sensor to divide this by 1000 convert it in to kWh? I could then create a new template sensor which multiplies this value with a cost per unit sensor to show my daily cost every day? Unfortunately, observing your consumption patterns takes a lot of time and effort, especially when the meter is somewhere in your basement and is full of numbers you can barely understand. Frient has an easy solution - let the Electricity Meter Interface do it for you. All you need is a compatible hub and your new frient wirelessly sends the meter data to your smart device. Now, you can detect when your electricity usage is the highest. You can also receive notifications when there's a sudden spike in consumption. This can help you identify - and then repair - broken appliances. Additional costs The Electricity Meter Interface will now start searching (up to 15 minutes) for a Zigbee network to join. The manufacturer documentation which is mentioned a few times in this thread indicates that maybe you could do more with the device, see 3.3.4.1.3 InterFaceMode, but I think there is a catch.

Jeg tror dog at watt grænsen skal sættes ret højt, eller at man skal have et mere specifikt formål med at finde et watt spike; for jeg endte med beskeder hver gang varmelegemet i forskellige husholdningsapparater startede opvarmningen. Nogle af dem gør det endda i mange korte perioder! In case of a weak or a bad signal, change the location of the connected gateway or strengthen the signal with a smart plug. Månedsrapport – morgen viser jeg blot, fordi det måske ikke er så logisk at finde ud af hvornår det er morgenen efter at strømforbrug – aflæsning måned variablen har fået en ny værdi. Derfor har jeg lavet ovenstående flow, som udløses hvis strømforbruget når over 2 kWh i foregående time. Er der brugt mere end 2 kWh, så får jeg en besked om, hvor mange kWh der rent faktisk er brugt.For et stykke tid siden bad frient mig om at teste en række af deres dimser, og i pakken var frient Electricity Meter Interface, som dog ikke kunne forbinde til SmartThings dengang. The Vue is installed in the consumer unit using CT sensor clamps that go around the mains and any other circuits you wish to monitor. The sensor.electricity_monitor only shows kWh consumed since it was installed so it’s not useful on it’s own to give me a current meter reading. I have created an input_text entity. In this I have input the meter reading as it was when I first installed my Freint device. This template sensor adds that value on to the value of the sensor to give me an up to date and accurate current meter reading that I can then use to report my usage to my energy company without needing to go to the garage and take a reading. The Electricity Meter Interface 2 serves as a Zigbee interface for your customers’ electronic meters. The Electricity Meter Interface 2 will collect readings and information from other meters, and send data via the Zigbee communication to appliances in the building. Your customer will then be able to follow their energy consumption through a display, their computer or mobile phone.

Ydermere, med Home Assistant seneste fokus på Strømforbrug (version 2021.8.0 og frem) samt deres helt nye "Energy"-fane i menuen, er det oplagt at rykke noget udstyr ind her, så vi kan begynde at udnytte de mange nye muligheder i HA for at beregne strømforbrug og -priser.Nu hvor vi har startet indsamlingen af data med den virtuelle Power By The Hour enhed, så sørger Homey automatisk for at gemme de værdier, som enheden aflæser. Der skal selvfølgelig gå noget tid, før der kommer data til hver af aflæsningsperioderne. If the Electricity Meter Interface does not send correct meter data, validate that the probe is mounted correctly to the meter. Emnet har også været oppe og vende nogle gange på vores Discord-server, og der er mange forskellige muligheder - fra at købe diverse Kamstrup dimser der installeres på el-måleren til et par tusinde kroner, til diverse IoT-enheder man klikker fast på hovedledningerne, der kan måle pulser.