Now you are properly prepared, let’s dive into how to build a fence, step-by-step. Just follow the below instructions: T marks’ on the plan point in the direction of the owner who has to maintain the wall, fence or hedge. You will need to install posts to support your new fence. Do this by following steps three to four in our ‘how to build a fence’ section.

Follow the manufacturer’s instructions or Structural Engineer’s recommendations for the screw pattern. Wooden posts are easier to handle. But as they’re buried in the ground, there’s a slightly higher risk that they’ll rot. However, if you choose decent timber that has been pressure treated then the risk of rot is low.

Project Enquiry Forms

Measure and mark out where your fence will sit then follow steps three to four of our ‘how to build a fence’ section to install the posts. Similar butt joint reinforcement connections may be made using two to four biscuits inset into matching grooves cut into the ends of the 4x4s. Alternatively, cut a matching groove in the butt ends and glue in a wooden spline. Dowels, biscuits, and splines all reinforce the alignment and provide some lateral reinforcement. For increased strength, apply construction adhesive to the cut faces and connect with 1/2″ or 5/8 inch through-bolts with washers or through the steel plates. Using a pen or pencil, make six small marks along both sides of the batten framing. Ensure these are at an equal distance from each other. Gate handles: These are used to provide a safe and easy way to open and close electric fence gates.

Insert the exposed end of the tape into the connector, making sure the tape is securely held in place. As we previously mentioned, it is a great choice to hire a tradesperson to build a fence for you. If you do intend to go down this route, it may be useful to know how much this will cost on average. Please note, the amount you pay will vary depending on a number of factors such as size and style of fencing. To connect electric fences, you will need to use connectors to attach the wires, posts, and other components of the fence. Start by planning your fence layout and determining the necessary materials, such as the type and number of connectors needed. Can electric fence wires touch each other?

Traditional Fencing

You can use our step-by-step ‘how to build a fence’ guide, however, this time you will be building the fence from scratch. Follow the below instructions to construct a stunning fence of your own: Featheredge fencing looks fantastic in any garden and is a great alternative to traditional panels. You will still use similar posts, but your fencing will have horizontal wooden boards instead of vertical panels. There should be two bolt holes for each connected piece. Most Codes require 1-1/2” between the edge of the wood and bolt hole, which doesn’t leave much space to off-set fasteners on a 4×4. A glued, plated and bolted nibbed tapered scarf joint is stronger than a half lap but not as easy to cut in limited space. Although it too has two cuts per 4×4, accurate sawing is more difficult. The skill level and aesthetics of the finished joint influence the choice of connection. A poorly sawn joint won’t make for a strong connection. Conclusion

Joining 4x4s for horizontal use instead of vertical use is done in a similar way. The orientation of the cuts should maximize lateral strength while preventing the retention of penetrating moisture. The stresses applied to the skid will also affect the type and orientation of the connection. A pull force versus a downward force affects the joint differently. Post to Beam Connection Coat the protruding piece of dowel with glue, or pour some glue in the holes of the upper pieces, and push it onto the dowels. Tap into place with a hammer if necessary. Depending on your budget you will need to decide if you prefer ‘Sawn’ or ‘Deluxe’ or Contemporary panels. Wire connectors: These are used to connect two electric fence wires together, either at the end of a line or where two lines intersect.Tighten the connector using pliers or other appropriate tools, making sure the connection is tight and secure. Strip the ends of the wires to be connected or attached, so that about 1 inch of bare wire is exposed. Your fence panels may need to be trimmed to reach the exact length of fence you require. You will need to first detach the framing batten from one end of the panel. Then you can trim the panel using a saw and reattach the batten.