Test your Work.Once all Port Forwards have been added and applied, you can test from outside your LAN.In this example, you would try to access https://203.0.113.48:8443 from another connection to verify the port forwarding was set successfully. Troubleshooting To reset a Ubiquiti ISP wireless device (ex. airMAX, airFiber, LTU) to factory defaults via SSH / CLI, log into the unit, and run the following as one command:

Ubiquiti airCube airMAX ISP Home Wi-Fi Access Point ACB-ISP Ubiquiti airCube airMAX ISP Home Wi-Fi Access Point ACB-ISP

The innovative antenna provides wide-area coverage, and the airCube’s elegant design allows you to place it anywhere. The airMAX® AC BaseStation connects wirelessly to the outdoor CPE, which is wired to theairCubeinside the home. Optional) If you would like to restrict access to the port forward, you can also add a Source IP/CIDR subnet mask. For example, adding 192.0.2.1/32 to Source IP/Mask would allow only 192.0.2.1/32 to access the Port Forward. The airMAX® AC BaseStation connects wirelessly to the outdoor CPE, which is wired to the airCube inside the home. This Gigabit Ethernet port is available to connect a 10/100/1000 Mbps device to the internet. It also accepts 24V PoE input and can be used to power the airCube.The Power Port can be used to power the airCube. This requires a 5V power adapter with a Micro-USB connector (not included). Then I did some speed tests. Sitting about 10 meters away from both Ubiquiti Unifi UAC-Pro (one of the enterprise access points) and AirCube, I got the following results. The supplied power adapter is 24V and it can power another Ubiquiti 24V device through the PoE out port without having to connect a PoE adapter into PoE In port. Doesn’t seem like a big deal but PoE adapters cost money so this feature will save a little bit. The UISP range meanwhile enables service providers to build and manage wireless networks for their customers. UISP products include the popular airMAX, airFiber, LTU, and Ufiber devices, delivering high-speed wireless and fibre connectivity for point-to-point and point-to-multipoint applications. For airCubes (ISP and AC): Push reset button and hold while powering unit.LED panel should blink fast several times, continue holding the reset button and the LED should turn off. Now you can release the reset button and the LED will flash slowly three times.

Ubiquiti Support and Help Center ISP Wireless - Ubiquiti Support and Help Center

Established in 2005, Ubiquiti has spent almost two decades manufacturing high-end, innovative devices for wireless networks. With a focus on offering exceptional performance at market disruptive prices, Ubiquiti's range delivers licence-free, simple to manage, and secure solutions which enable businesses to rethink their IT. Press the reset button on the device. While holding the reset button down, power the unit on. Wait 8 seconds then release the button (if you want to reset the unit to factory defaults, wait about 15 seconds or until the signal LEDs light up to indicate that the device is ready for recovery). Warning: Do not switch off,reboot ordisconnect the device from the power supply during the firmware upgrade process, as these actions will damage the device. The System screen allows enabling PoE Passthrough (the device has PoE in and PoE out – allowing to power two Ubiquiti devices with just one adapter), set the Timezone, and disable the LED. It’s not very bright though. By reloading fresh firmware to restore the device, this process can also be useful to recover devices that have appeared to fail when no other solution is working.Aircube can be configured as either AP or repeater. Every major configuration change results in having to restart the device. For this customer, AP is what I need as it will be connected to a wireless P2P link. Repeater is useful for situations where you want to connect to a router further away and place your own access point in the middle. Note: The device being Port Forwarded to should either have a static IP (with a router as default gateway) or a DHCP Lease Reservation. If not, your Port Forward may stop working on a router or device reboot. Steps: How to Port Forward on airCube Resets to factory defaults. The device should be running after bootup is complete. Press and hold the Reset button for about 10 seconds until the LED starts flashing and then becomes solidly lit. After a few seconds, the LED will turn off, and the device will automatically reboot. If no DHCP server is present or an IP cannot be obtained via DHCP, the radio will revert to 192.168.1.20 Please Note: The PSU included with this product is the EU version only. For UK use, please select the PoE Kit POE-24-24W-KIT from the ' Accessories, Add-Ons, and Extras' section above. Ubiquiti airCube airMAX AC Home Wi-Fi Access Point ACB-AC