To make this blaster even more battle ready, the Nerf N-Strike Elite Rapidstrike features not one, but FIVE separate tactical rails! With this many tactical rails you can easily customize your blaster to be your greatest asset in every blaster battle. With a fully automatic system, the Nerf N-Strike Elite Hyperfire can fire darts at the incredible rate of 5 per second. One downside to the Hyperfire’s extreme blasting system is that it tends to get hung up on old, worn down darts and is likely to jam.

Metal Targets - Swing Away Shooting Target - BB Target - Nerf Gun Targets - Small Shooting Target - Airsoft Gun Target - Animal Steel Target The Ultimate Nerf Blaster Book misspells the blaster as the Rapidstrike CS-18 and the Rapid Strike CS-18. Learn more about the Nerf N-Strike Elite Hyperfire on Nerf Wiki here! Nerf RapidStrike Nerf N-Strike Elite Rapidstrike CS-18 As far as differences go, there are plenty to choose from! For example, the two blasters vary greatly in firing range. The Hyperstrike has a 15 foot lead over the Rapidstrike and it even fires at a faster rate of 5 darts per second rather than the Rapidstrikes’ 3 darts per second.The RapidStrike is commonly modified to be smaller and "minimized" through the removal of most of the front half of the blaster. The full image gallery for RapidStrike CS-18 (Elite XD) may be viewed at RapidStrike CS-18 (Elite XD)/Gallery. The RapidStrike is likely a spiritual successor to the 2009 N-Strike Stampede ECS, due to various similarities between the two blasters, such as its abundance of tactical rails, fully-automatic firing mode, and eighteen dart clip. Full-size microswitch with roller-lever or simulated roller actuator, 10A rated or higher, to fit FCG and grip internals (optional, but recommended) Do NOT cut the wire ANYWHERE yet; leave it attached to the coil/spool. This goes for all rearwards-directed pieces of wire here; you will cut these to length later after connecting to more hardware.

Reactive Targets for Nerf, Rubber Band Guns, and others. Watch them fly into the air when hit. Great gift The speed of the RapidStrike's flywheels has two stages. The slowest stage occurs when the acceleration trigger is pulled; the second, faster stage occurs while both triggers are pulled. This cures the problem in other flywheel blasters where rapid fire decreases the flywheel speed and reduces range. The change in speeds can be heard when the clip is empty.

Keep collections to yourself or inspire other shoppers! Keep in mind that anyone can view public collections - they may also appear in recommendations and other places.

Despite this, and like other re-released Elite XD blasters, it features the same performance as its original counterpart. Alpha Trooper CS-12 • Firestrike • RapidStrike CS-18 • Rayven CS-18 • Rayven Stinger • Rough Cut 2x4 • Spectre REV-5 • Strongarm • Stryfe • Triad EX-3 The RapidStrike released early in the Philippines in May of 2013, due to the release error on the part of the distributor. [ citation needed] As its name suggests, the Elite XD RapidStrike claims to feature improved " Elite XD" internals, which boosts its overall firing power. It advertises an increased firing range of up to ninety feet in the U.S. (compared to the original Elite version's seventy-five feet), or twenty-seven meters in Europe (compared to the original Elite version's twenty meters).It features five tactical rails: one on the carrying handle, one on top, one underneath, and one on each side of the blaster. There are four strap points: one on the end of the handle, two on the end of the tactical rail, and one above the muzzle. The Nerf N-Strike Elite Rapidstrike CS-18, the very best there is. When you absolutely, positively, got to Nerf every melon-farmer in the room; accept no substitutes. The Nerf N-Strike Elite Hyperfire was released in 2016 and is one of the best blasters you could take into your next Nerf battle. Worker Mod Hand Thumb Screws Accessories for Nerf Stryfe Rapidstrike CS-18 ECS-10 2-in-1 Demolisher Hyperfire Blaster Toy Use flush cuts to chop off wire ends and solder blobs around edges of the two FCG switch PCBs. Do not remove the PCBs. Doing so removes support and insulation from the switch legs and makes wiring more difficult and reliability problems more likely.