First lift the arm rest (or whatever it's called), then gently pull up the centre consul, starting by the cup holder - you will find a join line inside the cup holder, pull on this and centre consul will come up (makes a horrible noise first time you do it) working forward towards the ash tray. Before I go out and buy the things that is needed for the retrofix, I would like to get confirmed that it is possible. Answer/Reject calls though your original car radio/navigation system via the FF (Fast forward) button.

Connect the connector of the mic lead to the connector of the loom under the steering column somewhere safe so it wont get caught. Direct CD changer port connection involving no FM Modulation for high quality sound without interference. It is unlikely that you will be able to use the later spec. BT/VC module (8M5T-19C112-AM) as the firmware in your stereo will be to old and it’s very unlikely that Ford have released the firmware to dealers to upgrade stereo’s â€" and I doubt the technician’s ability to do it correctly anyway. I used the Focus wiring although I’m told that the Fiesta wiring is the same except the microphone wire is shorter (not an issue here) and is about half the cost of the Focus wiring. If you still have difficulties, let me know exactly the model of stereo you have and I will see if I can help further.

There are two buttons on there stereo, both have a folder on them, and one has an arrow pointing into the folder, the other out of it. I've pressed these while the phone has been paired and it doesn't seem to do anything. Issuing voice commands doesn't seem to do anything either...

bluetooth was an optional extra, and is available with the standard CD6000 as well as the Sony head unit. To retrofit, you need (I did this a couple of weeks ago with these); Take the A pillar cover off and feed the mic lead down the gap, clip the mic to the top of the a pillar and refit. Thread the BT cable up to there and connect to the BT module, then mount the module using screw 1428699. The instructions are fairly straightforward and they do have good support forums. Also these units are fully upgradeable with a bluetooth enabled laptop to allow for firmware upgrades and support for new phones. On second thoughts, why install a bluetooth car kit when you can choose to look like a knob, like this guy? You will need:

YOU MAY ALSO CONSIDER

Phone connectivity was optional on the Focus MK2/MK2.5. This requires the optional Bluetooth/Voicecontrol system. This is a separate system that communicates with the radio over the CANbus network. Whether the car does or does not have the optional Bluetooth/Voicecontrol system can easily be determined by the radio stalk. Cars with Bluetooth/Voicecontrol do have a VOICE button on top of the radio stalk. On cars without Bluetooth/Voicecontrol the phone buttons on the radio act as mute buttons. If a Bluetooth/Voicecontrol module is connected the phone functions and menu of the radio will be active.

This “ How to” is for UK (RHD) Mondeo’s and some things may be on the other side of the car for European spec Mondeo’s. I have located the grey connector near the bonnet release BUT I can't see the 2 wires from the mic. The connector is a 22 pin. I have always used 0000 as the pincode, and I am unaware what to do if all steps have been remedied and the pincode still fails. Hope this gets it working for you. Refitting the bottom half of the cover is a bit fiddly, just make sure the bolt is loose fit in the cover, fit both bolt and torx screw, then fully tighten both. When refitting the top half, ensure the ears at the front are engaged properly.To remove the old switch undo the 2 small torx screws and slid switch out. Fit the new one, by siding in and refit the 2 torx screws. Looking up under the dash, locate the oblong lip, with a plastic post towards one end - it’s behind the plastic piece on the dash, towards the centre of the car â€" this is where the BT/VC module mounts. I have located and testet (whit an instrument that makes a sound when wires are put together) the pusible mic plug under the glovebox. Get your phone, go to bluetooth menu, scan for "new devices", this should hopefully now find something like "Ford Audio". On a successful pincode being entered, your phones bluetooth name will come up on the stereo display, and your phone will be "bonded" with your stereo for bluetooth usage.