IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11.

Using a client machine (e.g., a laptop), connect to the AP wirelessly (by associating to any SSID broadcast by the AP) or over a wired connection. Features No image available This guide contains a list of features supported by the Meraki Go platform and how to configure, manage, and troubleshoot them.Monitor and manage your account from anywhere, including setting usage limits and scheduling when your guest WiFi is available This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Each repeater in a wireless network will see its throughput reduced by 50%. A mesh network allowsrepeater access points tochain off of one another, and it is possible to see connections with multiple repeaters in them. Each repeater in the path to the internet will take the maximum throughput and divide it by half. Meraki Go Onboarding No image available If you have not yet added hardware to your account and configured it, you will need to go through onboarding. Configure separate WiFi networks for your staff, guests, and point-of-sale (POS) system to better protect your business and increase PCI compliance

i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Wireless networks of today are lightning fast, but it would surprise most people to know that only one device can send traffic at a time. This type of communication iscalled half-duplex, and is similar to how awalky-talky radio functions: only one speaker can be heard at any given time. What this means for client devices on a repeater is slower internet speeds. Static IPs are assigned using the local web server on each AP. The following procedure describes how to set the static IP:

ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. After locating a working gateway, the LED will turn green. If the LED continually blinks orange, it is unable to locate a gateway. Meraki Go Accessories No image available This guide houses articles regarding modules and accessories which work with Meraki Go devices.

Verify the gateway or another mesh repeater that has a route to the gateway and is within range of the mesh repeater. This can be done by moving them closer together with a line of sight and away from physical obstructions. If the device is going to be operated in the 5.15 - 5.25 frequency range, then it is restricted to indoor environment only. This device meets all other requirements specified in Part 15E, Section 15.407 of the FCC Rules.This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Troubleshooting A collection of articles to help troubleshoot common problems on Meraki Go hardware. Network problems come in varying forms and degrees of difficulty. This guide acts as a collection of all Meraki Go troubleshooting articles. See the table below for a listing of all troubleshooting documents. Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non con trôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. The LED will begin as orange while booting, then cycle through all colors while initializing and scanning for a gateway. On the L2TP PPP Options modal, select only the PAPauthentication method. Be sure the other authentication methods are de-selected. All other options can remain as the default. Select OKto continue.

Meraki Go is a cloud-based networking solution that lets small businesses self-manage their internet and WiFi. Cisco Meraki is committed to simplifying powerful technology to free passionate people to focus on their mission, and with Meraki Go, they're doing just that. Meraki Go empowers users who want an intuitive way to manage both WiFi and the ethernet networks at their businesses or small offices Seamlessly go between managing your network from your computer to the mobile app based on your preference This equipment is for indoor use only and the PoE device is considered unlikely to connect to an Ethernet network with outside plant routing, including campus environments.

Any changes or modifications no expressly approved by Meraki could void the user’s authority to operate this equipment. This Transmitter must not be co-located or operation in conjunction with any other antenna or transmitter. If possible, avoid the use of repeaters and mesh access points to maintain ideal throughput. The mesh can help with poor signal areas and struggling access points, but a gateway access point will always provide a better experience.