Ohms too low – the installed coil is below 0.6ohm which is the minimum resistance the device is compatible with. The port cover is sometimes a bit difficult to remove and replace. But you can swing the cover around for better access to the fill port. LP1มีให้เลือกหลายค่าโอห์ม แต่ละค่าโอห์มจะให้กลิ่นและรสชาติต่างกัน คอยล์บุหรี่ไฟฟ้าผลิตจากวัสดุเกรดอย่างดีปลอดภัยต่อการใช้งาน ทางร้านจำหน่ายคอยบุหรี่ไฟฟ้าแท้ 100% If I am honest I was expecting a bit more from this coil as it is mesh. But I can’t complain either! 1.2ohm MTL LP1 Meshed Coil Performance At the basic level this has a 700mAh battery which Smok say takes 70 minutes to charge using the USB Type C port at a 0.7A charge rate.

The SMOK LP1 coils are used with the SMOK Novo 4 pod device. Here’s what makes them such a great choice: SMOK LP1 Coils’ Leak-proof technology The pod is held in the mod perfectly, not a single wobble. This does not use a magnetic connection, the pod is gripped by latches in the pod bay.The pods feature a side-filling design, which makes refilling them easy and reduces leakage too. The included 0.9 Ohm mesh coil will deliver an MTL style inhale that creates a discreet amount of vapour with a cigarette-like feel. We'd recommend pairing it with 50/50 or high PG e-liquids for best results. The pods also feature an adjustable airflow, so you have the choice of a tighter or looser draw and can see what suits you best. This is adjusted by turning the pod to align the rubber plug with the air-inlet ring. I used my own e-liquid mix which is 50/50 PG/VG made from IVG Bubblegum Concentrate at 20% ratio. This is quite high a flavour ratio as I prefer plenty of flavour, but sadly this means it can be a coil killer sometimes. The pod is quite darkly frosted and for some reason seems to be bigger than 2ml? When filling it seemed to take ages as the liquid is even inside the mouthpiece area too. It is kind of middle of the road. I even tried it at 14 and 16W to see if there was any improvement – but nope 15W is the best really.

I am not getting the tasty Bubblegum blast I get from my OXVA Xlim 0.8ohm V2 pod sadly, but neither is this flavourless. Saying that the Xlim really does spoil you for flavour. A cute 0.69in OLED screen is provided to keep you up to date with all of your vaping data and device status. I love the fact you can change the coils, which is helpful financially and is less waste. Plus it does give you the freedom to try other coil resistances in the LP1 range.I recommend tipping the pod upside down when filling to make sure all of the inside of the pod is full. From the top you have the battery icon which shows a diagram of the charge remaining and below that in text is the % of charge. I recommend only replacing the coil when the pod is empty as you do get the whole contents empty out. If you can’t avoid changing the coil with a full pod, just make sure to have tissue everywhere! With the adjustment closed this is virtually closed off to incoming air too. But there is still enough to trigger the device to fire which surprised me. This is way too tight to use at this setting for long periods. The 0.8 Ohm and 0.9 Ohm LP1 mesh coil feature a specially designed lattice build that can heat more e-liquid at a faster rate, improving flavour. However, the LP1 0.8 Ohm standard coil produces a more mellow flavour than the mesh version. Finally, the 1.2 Ohm LP1 coil produces the most discreet amount of vapour and feels the closest to a cigarette. The three seals on each coil prevent leaks from occurring when installed in the Novo 4 pod.