After pressing the ‘+’ key the current number of LH100 throttlenotches is shown. 28 throttlenotches is the default for version 3.0 E Bike Sd Controller Water Resistant Sensitive Thumb Shifter Panel Online At Best S In Desh Daraz Com Bd The display (and scooter) can be powered on or off by pressing and holding down the red power button. Odometer and Trip Though the most common variant of the QS-S4 is the trigger or finger throttle, QS-S4 also comes as a thumb style throttle or can be modified to be controlled by thumb throttle. Some retailers offer the thumb throttle as an upgrade that must be professionally installed by disassembling and soldering new connections onto the original throttle. There are also QS-S4 versions that come as a thumb-throttle direct from the factory. The QS-S4 is designed in such a way to be compatible with a wide range of electric scooters (and even e-bikes) that operate on different voltages, with different motors and tire sizes (among other things).

The Brainpower Motor Controller Model LH100 6 Wiring Schematic is an industry-standard wiring diagram used by technicians and engineers for connecting motors and controllers. This wiring schematic provides a straightforward way to wire and connect motors with controllers, making it an integral part of any electrical project. Setting the locomotive decoder to a particular speed step mode is done in CV29 of the decoder. For details, see the Digital plus by Lenz ® "Information for locomotive decoders". All versions of the QS-S4 use a 5- or 6-pin connector that communicates with the controller via the UART protocol over TX and RX lines. USB Port

QS-S4 LCD Throttle

With the LH100 you can (depending on the software version of the command station you are using) control, assemble and disassemble multi-unit consists. Insert the 5-pin DIN-connector into a LA152/153 connection plate that is connected to SET02 or Atlas Commander, or to any other XpressNet 5 pin DIN plug. Dual Motor Driven Part 1 Lcd Display 2 Bldc Controllers 24v36v48v60v400w 5000w For Electric Scooter Motorbike Mtb Atv Snowmobile History Review Aliexpress Er Phoebeliu Ev Parts Tools Alitools Io

P-settings allow scooter riders to customize their ride. The top 5 programmed features in both types of LCD finger throttles are:For specific settings for your electric scooter (including factory default), lookup your scooter settings in our database. P5 — Zero start. Enables or disables “zero start” feature which allows the scooter to be launched from 0 mph. When disabled, the scooter must be rolling a low speed before the motor will activate. With the key you cause an emergency stop for the entire layout. When this key is pressed, all locomotives will immediately stop. By pressing this key again, the emergency stop is released. This operation of this key can be configured using the set This manual is written with the assumption that the LH100 is configured for the English language display. You can configure the LH100 for either English or German display. See section 14.2.2 for a description on how to configure the language of your LH100 display.

Headlight error code 13: This error code is related to the LED lights on your scooter. The connection may have come loose, or the LED itself has been damaged. To troubleshoot, you can test the LED with multimeter set in diode test mode.In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service. The QS-S4 LCD has superseded older versions of the unit, including the TF-100 and LF-100 finger throttles; in most cases the QS-S4 is not interchangeable with these models, but this will depend on your electric scooter model. Thumb Throttle In this section you will learn about basic locomotive control using the LH 100. When you want to control a locomotive, you have to call it up first. There are three different ways you can call up a locomotive you want to control: