Hi there, I want my E7350 install OpenWRT, but the device installed the newest offical firmware already. Unclog your network with twice the bandwidth. Wireless signals transmitted on 2.4GHz and 5GHz simultaneously allow for the strongest connection possible. Choose your lane depending on whether you need range or performance. Power ON your modem and connect an ethernet cable from the modem to the internet port of the router. If you are replacing an existing router, make sure that it is disconnected, turned OFF, and removed from the modem. Yes, 1x 1.1, 1x 1.1 Device, 1x 2.0, 1x 2.0 Device, 2x 2.0, 3x 2.0, 4x 2.0, 5x 2.0, 6x 2.0, more than 6x 2.0, 1x 3.0, 2x 3.0, 3x 3.0, 4x 3.0, 5x 3.0, 6x 3.0, more than 6x 3.0, Mod, 1x Device, 1x Header, 1x OTG, 1x µUSB (charging), 1x Power only

Belkin Official Support - RT1800 Downloads Belkin Official Support - RT1800 Downloads

A parent node is the router (with the EasyMesh feature enabled) that is connected to your modem. This can be either a Belkin RT1800 or a Belkin RT3200. Default Guest network names - Belkinxxxxx-guest for the 2.4 GHz network and Belkinxxxxx_5GHz-guest for the 5 GHz network (where xxxxx represents the last five digits of the serial number)Memory: 248708K/262144K available (7032K kernel code, 630K rwdata, 1416K rodata, 1276K init, 243K bss, 13436K reserved, 0K cma-reserved, 0K highmem)

Belkin RT1800 v1 [OpenWrt Wiki] Techdata: Belkin RT1800 v1

So you're getting boot partition 2 load each time instead of partition 1 where you flashed openwrt successfully but it's refusing to boot into it.

Connect to the default WiFi name of the parent node. The default WiFi name is Belkinxxxxx or Belkinxxxxx_5GHz (where xxxxx represents the last five digits of the router's serial number). Belkin's liability for damages caused by slight negligence, irrespective of its legal ground, shall be limited as follows: (i) Belkin shall be liable up to the amount of the foreseeable damages typical for this type of contract due to a breach of material contractual obligations; (ii) Belkin shall not be liable due to a slightly negligent breach of any other duty of care applicable. The aforesaid limitations of liability shall not apply to any mandatory statutory liability, in particular to liability under the German Product Liability Act (Produkthaftungsgesetz), and liability for culpably caused injuries of life, body or health. In addition, such limitations of liability shall not apply if and to the extent Belkin has assumed a specific guarantee. If you have any OpenWrt version running on the router, try sysupgrade with the proper sysupgrade image from the Firmware Selector.

OpenWrt Wiki] Techdata: Belkin RT3200 [OpenWrt Wiki] Techdata: Belkin RT3200

This warranty is in addition to, rather than replacing, statutory rights that you have as a consumer, as may be described below. EasyMesh allows you to set up a mesh system with other EasyMesh-certified devices to extend your WiFi.If your warranty claim is valid, Belkin will replace the screen protector with, at your option, a similar SCREENCARE+ Application System product or a screen protector product that you can apply yourself with the included Easy Align tray. Older phones may require a screen protector product you apply yourself.

Belkin | Ireland Belkin | Ireland

Belkin does not give any warranty: (a) for application services provided by Belkin or any third party; or (b) that a third party service the product needs will always be available. Belkin does not warrant any wear or damage related to the user's device.So if you can get serial working properly, the boot loader allows uploading through tftp without a header. So sysupgrade image. UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID D29FC0E4-6E85-4239-B051-7578E62A59E4, small LPT model