We decided to cut down two sides of the beam to make it 6″x6”. But this was a little more difficult because the table saw we were using can only cut 3“deep (total of 6″). We were off by 2″ on one side. Beams are an essential part of construction, as they provide the required structural support between two areas. They can be made from metal or wood—in this article, we will be covering wood beams along with their characteristics and usages. Hand tighten the bolt and then use some sort of lever to tighten it further, I used a large screwdriver.

Like I stated before, the beam I am using is a 8“x8″ beam my brother had leftover at his house. But we felt that an 8″x8” beam was too big for the space. Set the suspension height at 60 – 80cm above the table top. This will allow you to see your fellow diners and not bang your head! Remember, in step one you determined the location of where the center of your beam will be plus the center of the trusses. You are now going to prep the 2″x6″ wood ceiling support to attach to these marked locations. Then, mark two more spots on the board, 3-1/2″ from each end to the center of the board (3″). These marks are where the eye bolts will be placed to hold the metal chain.Whether you dine in style under the light of a modern wooden hanging light or in the comfort of a more rustic style, here are some tips for the new wooden hanging light in your dining room:

Then, spray paint the pieces according to the directions on the can. Remember lighter coats are better when applying spray paint. Once one side was cut to the 6″, the other side could be cut on the table saw. This second cut is the 2″x6″ board for the ceiling support. We cut this board to 27″.Please copy the voucher code, go to the basket and paste it into the voucher code box. To the Cyber Monday Sale Place the wood ceiling support onto the ceiling and align the sides of the board on the marked lines. Also have the pre-drilled holes aligned for the center of the truss.

Take one of the screws and push it through each of the pre-drilled holes. Make sure you apply pressure so that it indents into the drywall. However before installing the wedge bolts I had to mark the holes to drill on the ceiling. To do this I made a T-profile from some scrap wood. This way I could use the flat part of the T to place it against the wall and then use the markings on the end of the T to mark the ceiling. This way the beam would be perfectly parallel to the wall. Normally, the light will appear purpleor violet, and the skin will not fluoresce. However, certain bacteria, fungi, or changes inpigmentation of patient skin will cause the affected area of the skin to change color under light; hencethisis used for inspection and detection of certain fungal infections. Wood's light is not atherapeutic or treatment device. [2] Make sure to pay attention to the colour rendering. This is another feature of the light source which can found alongside the luminous colour in the product details section. If the colour rendering is below Ra 80, it won’t be ideal for dining. Now you need to determine where the trusses (studs) are in the ceiling and which way they are running. You have to attach the ceiling support to at least two trusses in four places to hold the weight of the beam.You’ve decorated your home in a bright Scandinavian style but you’re still looking for something to bring out the natural character of your home? Perhaps you even live in a modern, minimalistic apartment but want a piece of furniture that brings warmth to the ambience of your humble abode? If any of these rings true, look no further! When the bolts were installed, I attached the first chain and marked the length I wanted it to be. I then marked this length on all four chains and cut them to length using an angle grinder. With this done I attached all chains to the bolts. TIP: It would have been easier to use an Oscillating Dremel but we could not find my dad’s tool anywhere, so we improvised. Remove the metal from the beam, then measure the distance from the marked line to the shorter end of the metal. This mark should be right around 1″. Once suspended from the ceiling, wooden pendant lights often sit just above eye level, so they’re sure to attract attention. This makes them a perfect fit for the dining room – more precisely, for over the dining table.

The second bend is where the beam will sit. And the easiest way to mark this bend is by using the beam. Place the flat metal bar (there will be one bend) on a flat surface. Then, place one end of the beam onto the metal bar so that it is snug against the first bend. On the front of the wood ceiling support, mark each corner of the board 1-1/2″ from each side; there will be four marks. These four marks will be where the wood is attached to the ceiling. Pendant lights work well in almost any interior style – after all, you always need light for you dining table! SIDE NOTE: There is electrical work involved in this project, so please make sure you turn OFF the power to the lightbox . I am not an electrician and you should be aware that there are dangers in doing this project yourself, so please be careful. STEP 1: MARKING YOUR CEILING FOR PLACEMENT

Site Customisation

Complement the lighting in your dining room using good orientation lighting, such as wall lights. These provide a soft, shadow-free light and can be switched on in addition to your pendant light to avoid strong light-dark contrasts in large dining rooms, which helps to reduce eye strain. Now, mark the middle of the trusses for where the end of the wood ceiling support will sit. This will be the distance from one wall to your first marked beam center plus 3″ (half of the size of the wood support). SIDE NOTE: Our center point was centered between two trusses, so adjust these steps to fit your space.