Styrene (also known as Hi-Impact PolyStyrene) is the most commonly used plastic in molded plastic kits (Model Railroad, Automobile, Airplane and Ship). For that reason, we have chosen Styrene as the medium in our New FineLine Structural model parts for compatibility in kit-bashing. It may be combined with wood, metal and other plastics using special glues or cements. Styrene has a tendency to be brittle, especially after lengthy U.V. exposure or painting. It is easily warped by solvents, so care must be taken when cementing flat sheets for walls, and reinforcement bracing is recommended. When constructing closed tanks or structures, venting is recommended to allow the inside and outside temperatures to equalize. Styrene has excellent forming characteristics and bonds rapidly and permanently. Styrene plastic cuts easily using the “scribe and break” method. Only use Enamel, Alkyd Oil, Latex or Acrylic paints specified for Styrene plastics. ACRYLIC PS-47 through 59 make excellent industrial vents when modified by adding Styrene Strips to every other slat. They can also be used as window awnings.

ABS has been hailed by professional modelmakers as “the best all-around construction material since wood”. Stronger and more rigid than many metals; easier and more flexible to work with than any previous plastic; cleaner and more durable than wood, ABS structural shapes by PLASTRUCT have been used for engineering design models on an international scale since their introduction. ABS is also one of the best plastics for heat or vacuum forming and, of course, has excellent bonding characteristics, not only to itself but to other commonly used plastics. recommend that goods are returned by recorded or insured delivery. If you would like to phone our despatch department For fast, clean, accurate cutting of Styrene Shapes, Tubing, Strip and Rod, simply scribe with a hobby knife and snap. When cutting Sheet Styrene, make all scribes first and then bend downward one side at a time until it snaps clean. All Acrylic Rods may be cut using a fine tooth saw blade. Cut ends should be polished using a flame or WET & DRY fine grit sand paper. Bending may be accomplished by carefully softening the Acrylic using a torch flame or electric stove burner.Below you will find useful information and characteristics of the most commonly used plastic materials to assist you in using them properly. The most commonly used plastic materials are: If goods are returned as faulty, generally we will provide a replacement. If the item is of a ‘ready to go’ type model eg. Exceeds the most demanding specifications for temperature, leak-proof (Hermetic) and pressure requirements When surfaces larger than a single sheet are to be covered, in most cases, the patterns are designed to allow easy and undetected joining of multiple sheets. FINISHING & PAINTING

For smudge free bonding, apply a small amount of solvent cement with a blunt tipped syringe needle at one end of the parts to be joined and allow the cement to flow, through capillary action, the entire length and breadth of the joint. This will provide a “weld” as strong as the surrounding areas. Be sure to use PLASTRUCT Plastic Weld or Bondene Cements. Professional model makers have used plastics as virtually their sole working material for the past 30 years. However, hobbyists, miniaturists and amateur model builders have, for the most part, continued to use wood, card and brass for their models. There are, of course, applications where those materials are suitable or desirable. But in most cases, Plastruct should be your material of choice. to examine the product you must have done so without damaging or marking the product in any way). It should be Diecast – Explore Our Range of Diecast Models At Scale Model Shop, we supply a wide range of diecast models, specialising in aircraft, cars, and tanks. Diecast models are a miniature replica made using a die casting or metal casting method. They are usually made of zinc or lead alloy and come fully formed in a single piece which portrays the vehicle in a smaller scale. Diecast models are much more than a simple toy, they demonstrate a higher level of quality than other plastic kits, due to the higher shelf life. This is great for any enthusiast collector as you can display for years and pass it down to the next generation. It doesn’t matter if you’re just starting out or have been collecting for years, there is no denying how appealing a diecast model collection is. Browse through our range of brands available, including Corgi, Diecast Masters, and Greenlight – there is plenty to choose from!Copolyester (also known as P.E.T.G.) is tougher and less prone to split or shatter than Acrylic. It has excellent clarity in sheet form, and is resistant to stress whitening. It is easily formable and not prone to warp. Copolyester is quite stable and bonds well to itself, however with most other plastics, a special industrial grade Cyanoacrylate Glue is recommended. Accepts most paints, including lacquer. Cement Guide For professional quality painting of structures, it is recommended that, when possible, construction of the main components be completed and painted assembled. Paint sub-assemblies and other detail parts before attaching to the main structure. Use solvent cement sparingly during final assembly so paint will not run. For best results in landscaping, plant in groups and use different heights of trees to represent varying ages of the trees as well as for creating depth of field. As you move further from the viewing point or higher in the mountains, use shorter trees. Shorter trees may also be used for potted or tubbed trees. The material used in our Traditional Round Tubing medium is Butyrate plastic. It has proven to be ideal because it is so convenient to work with. It can be cut, turned, drilled, painted and easily cemented. The Tubing and Tubing Fittings are manufactured to provide a good friction fit and maintain the outside diameter; splines on the male Fittings accomplish tight fit and prevent undesired rotation and still allow intentional turning. This feature permits cementing to be a final operation. The telescoping sizes of the pipe combined with the workability makes improvisation quite simple.

You have the right to cancel within 7 working days after the day you take receipt of goods. You must notify us within Please note many modelers refer to scale as a fraction, while others refer to it as a ratio. For instance, 1/48 is also referred to as 1:48. Both are correct. POPULAR MODELING SCALES HOBBY SCALE Basic construction of building shells is usually of a rigid material such as Acrylic, Styrene, Foamboard or plywood. Plastruct Plastic Patterned Sheets can then be applied to create realistic simulated finishes. For PPE, you'll for sure need gloves made of neoprene rubber rather than surgical latex types. It will remove the oils in your skin. And definately goggles for the eyes. Had some spalsh in my right eye one time while working on a plane, and it will make a grown man cry!! lol Ventilation is also a must - got 'happy and giggly' due to it one time with my supervisor one time cleaning another fuel tank where ventilation was an issue. Fittings can be more readily attached to Tubing, particularly in sizes 5/16″ and over, if the pipe is screwed onto the Fitting. Always rotate the Tubing in the same direction whether attaching or removing the Fitting. STYRENEWe are pleased to provide the following collection of creative tips for working with PLASTRUCT Plastic Model Parts.

Plastruct Model Parts and Accessories are manufactured in several plastic materials. The choice of material was based upon the final use of the Product as well as workability and price. Butyrate can be lathe-turned in the same manner as brass or Cast Acrylic. Grind the cutting tool to provide chip clearance. The resultant turnings will have a polished surface. This material can also be drilled, tapped, carved or saw cut. Very slow speed is required for machine sanding. You have many options when it comes to Plastic Welding and Assembly. The Emabond Process offers certain unique advantages when compared to alternative forms of assembly such as: PS-25, 26 and 27 make excellent road and highway guardrails when cut into strips and mounted on square posts.This service does not deliver on a Saturday or Sunday. If you would like Saturday delivery please call us on 01782 409310. ABS hand rails and stair rails may be curved to fit circular applications by softening them in warm water or heating with a hair dryer. Stairs may be modified to fit the circumference of a tank or other curved surface by cutting off the stair stringer from the side to be cemented. Tape the stair in place. Attach each stair step separately. For the various materials found in PLASTRUCT’s Catalog, the following cements are recommended: STYRENE These plastic sheets are easily cut with a hobby knife or scissors. For sheet application to a substrate surface, a general purpose spray adhesive or our GES-2 Silicone Adhesive is recommended. In some cases, our Plastruct Plastic Weld or Bondene Cements are preferable, however, caution must be taken to ensure proper application; too much solvent cement may melt the plastic sheet. To remove solvent stains from Styrene sheets, use a Pink Pearl eraser or fine steel wool.