The largest diameter AWG size is 0000 (4/0) which is pronounced ‘four aught’, representing a diameter of .46″. The smallest diameter is 32 AWG, representing .00795″. The wire size chart below shows allowable ampacities of insulated conductors rated up to and including For more information regarding wiring and cables, see our comprehensive guide here. AWG Gauge Table AWG gauge The n gauge wire diameter d n in inches (in) is equal to 0.005in times 92 raised to the power of 36 minus gauge number n, divided by 39: Increasing gauge numbers denote logarithmically decreasing wire diameters, which is similar to many other non-metric gauging systems such as British Standard Wire Gauge (SWG). However, AWG is dissimilar to IEC 60228, the metric wire-size standard used in most parts of the world, based directly on the wire cross-section area (in square millimetres, mm²). The AWG originated in the number of drawing operations used to produce a given gauge of wire. Very fine wire (for example, 30gauge) required more passes through the drawing dies than 0gauge wire did. Manufacturers of wire formerly had proprietary wire gauge systems; the development of standardized wire gauges rationalized selection of wire for a particular purpose.

The AWG tables are for a single, solid and round conductor. The AWG of a stranded wire is determined by the cross-sectional area of the equivalent solid conductor. Because there are also small gaps between the strands, a stranded wire will always have a slightly larger overall diameter than a solid wire with the same AWG. The AWG system states areas of round copper wires in "circular mils", which is the square of the diameter in mils. 1 mil =.001 inch. The common U.S. wire gauges (called AWG gauges) refer to sizes of copper wire. The resistivity of copper at 20 C is about This table uses this value of resistivity, but it is known to vary by a few percent based on purity and process of manufacture. AWG wire

Wire Size Chart and Maximum Amp Ratings

The AWG gauge system only applies for solid, round, non-ferrous conducting wires. Keep this in mind when evaluating wire size and type for your application, as AWG doesn’t apply to stranded or non-round wires. AWG Gauge Sizes for Home Wiring, Auto Wiring, and Boat Wiring The n gauge wire diameter d n in millimeters (mm) is equal to 0.127mm times 92 raised to the power of 36 minus gauge number n, divided by 39: The U.S. wire gauges (called AWG gauges) refer to sizes of copper wire. This table corresponds to a resistivity of

Results may change with real wires: different resistivity of material and number of strands in wireconductors in raceway, cable, or earth (directly buried), based on ambient air temperature of 30°C (86°F). By definition, No. 36 AWG is 0.005 inches in diameter, and No.0000 is 0.46inches in diameter. The ratio of these diameters is 1:92, and there are 40 gauge sizes from No.36 to No.0000, or 39 steps. Because each successive gauge number increases cross sectional area by a constant multiple, diameters vary geometrically. Any two successive gauges (e.g., A and B ) have diameters whose ratio (dia. B ÷ dia. A) is 92 39 {\displaystyle {\sqrt[{39}]{92}}} (approximately 1.12293), while for gauges two steps apart (e.g., A, B, and C), the ratio of the C to A is about 1.12293 2 ≈ 1.26098.

American Wire Gauge ( AWG) is a logarithmic stepped standardized wire gauge system used since 1857, predominantly in North America, for the diameters of round, solid, nonferrous, electrically conducting wire. Dimensions of the wires are given in ASTM standard B 258. [1] The cross-sectional area of each gauge is an important factor for determining its current-carrying capacity.Maximum current for chassis wiring. Data from Handbook of Electronic Tables and Formulas for American Wire Gauge. The maximum current for power transmission is less.