With an exceptional print size of 300 x 410 mm, you can make amazing prints in the best quality! The V400 is also suitable for large print formats! Firmware retraction gives an advantage compared to Slicer retraction, it can be modified during a print (from Mainsail or KlipperScreen) and therefore the same gcode can be printed with different parameters without the need to be re-sliced. A higher belt tension can be set by adding more 50 cent coins, and a lower belt tension can be set by removing 50 cent coins. Our review copy of the FLSun V400 came with a copy of Ultimaker Cura 4.13.1 and one generic profile to get started. It also comes with the Moonraker plugin so it can connect the printer with your PC. The manual walks you through setting up the printer based on their previous model, the FLSun Super Racer.

Then upload printer.cfg, macros.cfg, neopixels.cfg and adxl345.cfg files located in Configurations directory. The tool for adjusting the timing belt tension can also be used for the FLSUN Super Racer (SR), as the timing belt spacing is the same as for the V400. The measurement should be taken at mid-height, between the lower and upper bearing roller of the timing belt.FLSun only included directions for using Cura. Trying to set up PrusaSlicer with the start and end gcode included for Cura doesn’t appear to work. The FLSUN V400 user manual recommends adjusting the tension of the toothed belts every 2 months. But how can the toothed belt tension be measured reproducibly? There are two variants to choose from - one with the weight on the right-hand side and one with the weight on the left-hand side. The Flsun V400 is an extremely user-friendly Delta 3D printer. The 3D printer features extremely fast printing speeds of up to 600 mm/s and an acceleration of 10 000 mm/s². This saves you more than 70% of the usual printing time while still producing high-quality 3D prints. Files are sliced in Cura just like any other printer, then are transferred to the V400 via the Moonraker plugin, dragging and dropping into Mainsail, or by using the supplied USB drive. Printing on the FLSun V400

Számos 3D-nyomtató Bowden extruderrel van felszerelve, mert ez nagy nyomtatási sebességet biztosít, és a Direct Drive extruderrel ellentétben kisebb súlyt fektet a mozgó Hotendre. Az Flsun azonban valami egyedit alkotott a V400 nyomtatóval: a hotendet és az extruder házát kombinálták, ami egy különösen kompakt és könnyű rendszert eredményezett. Valószínűleg sikerült a piacra hozniuk az egyik legkönnyebb és egyben leggyorsabb Direct Drive extrudert! Then the new image was written to the SD card using Raspberry Pi Imager, inserted into a fully disconnected Speeder Pad and left to update (took about 20 mins). Finally all the calibration was done again but its easier with the new firmware. Bed Level now does both phases in one go and leaves you with a screen to set Z0. Then goto Config – Input Shaper – there is now an Auto Calibrate button – there is no need to comment out parts of the cfg files or do the SAVE-CONFIG – this is all now done for you.

Note: Flashing the imager will reset all configurations and lose all data on your pad so ensure you have copies of anything you may want to keep. Az Flsun V400 egy rendkívül felhasználóbarát Delta 3D-nyomtató. A 3D-nyomtatót rendkívül gyors, akár 600 mm/s nyomtatási sebesség jellemzi! Ezzel a szokásos nyomtatási idő több mint 70%-át takaríthatja meg, miközben kiváló minőségű 3D-nyomatokat készít! A könnyen használható 7 hüvelykes LCD érintőképernyő különösen felhasználóbarát kezelést tesz lehetővé! A kijelzőt a KlipperScreen működteti. The Cura Profiles were updated by following the details in THIS file and a new V400 added to Cura (this is V400 #2 on my system and has 600mm/s as the max speed. V400 motherboard doesn't support DFU mode, so it's not possible to install the firmware directly. It's therefore necessary to install it manually.

The correct toothed belt tension is indicated by a pointer that is vertical and parallel to the printer frame. In my case, this is achieved with 6 50 cent coins, i.e. 46.8 grams in weight. I also recommend using a microSD extension for future updates to avoid removing the cover each time. Start Gcode: START_PRINT BED_TEMP={material_bed_temperature_layer_0} EXTRUDER_TEMP={material_print_temperature_layer_0} i)And wait until the bar is fully charged and green, this may take several minutes (10/15 minutes)： A nyomtatóhoz előre telepítve van a Klipper Firmware. A Klipper első osztályú nyomtatási élményt és nagyfokú felhasználóbarátságot biztosít – akár WiFi távirányítóval is!Many 3D printers are equipped with a Bowden extruder because it provides high print speeds and puts less strain on the moving hotend than a direct drive extruder. But Flsun has created something unique with the V400: the hotend and the extruder housing have been combined, resulting in a particularly compact and lightweight system. They will probably succeed in bringing one of the lightest and at the same time fastest direct extruders to the market! An easy-to-use 7-inch LCD touchscreen makes handling particularly user-friendly! The display is powered by KlipperScreen.