The General section is used to set up some of device managerial parameters, such as changing device name. For more information on the General section, refer to figure and table below. Maximum time (in seconds) the button can be held to perform an action, after which no action will be performed. Por la presente, TELTONIKA NETWORKS declara que este RUT240 cumple con los requisitos esenciales y otras exigencias relevantes de la Directiva 2014/53/EU Core parameters or simply parameters that apply to each file type are the size and common name of the generated file(s).

No encryption | WPA-PSK | WPA2-PSK | WPA-PSK/WPA2-PSK Mixed Mode | WPA3-SAE | WPA2-PSK/WPA3-SAE Mixed Mode A TELTONIKA NETWORKS ezzennel kijelenti, hogy a RUT240 típusú berendezés teljesíti az alapvető követelményeket és más 2014/53/EU irányelvben meghatározott vonatkozó rendelkezéseket Specifies when the period of counting data usage should begin. After the period is over, the limit is reset and the count begins over again. Fixed Linux vulnerabilities CVE-2021-4148, CVE-2022-0480, CVE-2022-1055, CVE-2022-0886, CVE-2022-2663, CVE-2022-36879 for v5.4 The DHCPv6 protocol is used to set up an IPv6 interface which obtains its configuration parameters automatically via a DHCP lease.

Teltonika RUT240 Compact, Industrial 4G LTE Router with WiFi

To make the DHCP Server section visible, set interface protocol to Static. DHCP Server: General Setup The Firewall Settings section is used to specify to which firewall zone if any this interface belongs. Assigning an interface to a zone may provide easier configuration of firewall rules. For example, instead of configuring separate rules for each WAN interface, you can add all WAN interfaces into a single firewall zone and make the rule apply to that zone instead. RUT240 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.

Expanded the data that is sent to the Cumulocity cloud with device log, mobile data usage nd GPS dataPresumes peer to be dead after given amount of LCP echo failures. Leave it at 0 to ignore failures. This device must accept any interference received, including interference that may cause undesired operation.

Do not leave your device and its accessories within reach of small children or allow them to play with it. They could hurt themselves or others and could accidentally damage the device. Your device contains small parts with sharp edges that may cause an injury choking hazard. By default, the lists are empty. A set certificates generated using 'Simple' file type would look something like this: The Access Concentrator to connect to. ISPs used Access Concentrators to route their PPPoE connections. Usually, the settings are received automatically, however in some cases it is required to specify the name for an Access Concentrator. Leave empty to detect Access Concentrators automatically. Power on and connect with an Ethernet cable to the LAN port and your router should have reset to factory default settings. Please Note: This product has been discontinued. For the replacement model, please see the Teltonika RUT241. Teltonika RUT240 Compact, Industrial 4G LTE Router with WiFi

Teltonika RUT950 Dual SIM LTE Router with WiFi

Härmed intygar TELTONIKA NETWORKS att denna RUT240 är i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 2014/53/EU

TELTONIKA NETWORKS декларира, че RUT240 е в съответствие със съществените изисквания и другитеприложими разпоредби на Директива 2014/53/EU Fixed Routing/NAT Offloading section display in Network -> Firewall -> General Settings when device is not supported The DHCP force function ensures that the device will always start it’s DHCP server, even if there is another DHCP server already running in the its network. By default the device’s DHCP server will not start when it is connected to a network segment that already has a working DHCP server. A Phone Group is a collection of phone numbers that can be used as the recipient in SMS & call related services instead of specifying every number individually. The phone group list is empty by default thus, you must first add at least one new group before you can add phone numbers to it. To create and begin editing a phone group, follow these steps: PoE (passive) Passive PoE over spare pairs. Possibility to power up through LAN port, not compatible with IEEE802.3af, 802.3at and 802.3btGenerating each type of file (excluding 'Simple') requires setting some parameters. This section provides an overview for parameters used in TLS certificate generation.