The VGA-Vertical Bottom Mode gives only 20mm clearance and does not allow for fan or radiator installation. With any motherboard it does not allow fan or radiator support in the bottom. Dual Chamber Design for Cable Management The dual-chamber design behind the motherboard tray made cable management a simple job. RECENSIONE: mi piace molto questo case, decisamente più piccolo del tuf gaming501 (il che devo dire che è lo stesso un case da paura, ma che per motivi di spazio e stile ho deciso di cambiarlo).

Unsurprisingly, because there is more airflow resulting from the higher fan speeds (and the mesh front), thermals are a little better with the Mini Air. The 7 Slot Mode has space for up to ATX motherboards. This mode will reduce radiator support – removing support for a top radiator when using any size motherboard. When using an ATX motherboard, the bottom radiator can only be 240mm, but with ITX and M-ATX you can install up to a 280mm radiator.A 120 mm fan can be mounted to the rear panel. Air inlets at the bottom, roof, and side are equipped with magnetic dust filters, so the interior remains clean. The Lian Li O11 Dynamic Mini accommodates CPU coolers up to 170 mm in height meaning there are virtually no limits when choosing a powerful processor cooler. This case also supports large form factor graphics cards up to 395 mm in length. Hard Drives and PSU options TEMPERATURE OTTIME, la circolazione dell'aria è OTTIMA, nel vecchio case avevo un castom liquid, ho deciso di mettere in questo nuovo case un AK620. le temperature della cpu sono quasi identiche. visto che l'aria in espulsione è molto vicina al dissipatore. When I first received the O11 Air Mini, I didn’t think I would like it. After all, the standard O11D Air wasn’t as popular as the PC-O11 Dynamic, the company ditched the pretty glass panel, and often, included case fans just aren’t all that good. Small tower with big airflow, the O11 AIR MINI provides modular design for ATX, M-ATX or ITX motherboards. Being all about the air, O11 AIR MINI has a spacious interior to accommodate multiple confirgurations of fan and radiator setups to maximize the airflow.

The VGA-Vertical Top Mode gives more clearance for fan installation in the bottom, with 60mm total clearance. With an ATX motherboard only 240mm radiators can be installed in the bottom.

Peripherals

in questo lian li 011 AIR MINI, se si hanno i cavi cablati si ha qualche problema con il cave-management , quindi bisogna trovare un compromesso. La ventilación es muy buena y no se suele llenar de polvo sin facilidad. Tenía un Asus TUF GT 301 y ese si se llenaba de polvo bastante. Regarding liquid cooling, the levels of radiator support that this case offers varies depending on your chosen hardware configuration. We will discuss this further later in this review. But this couldn’t be further from the truth with the O11 Air Mini. I like the look of its front mesh panel more than glass, and it performs a smidge better. The included fans are actually reasonably good, and the case has a more practical interior with support for ATX power supplies, instead of being limited to SFX-only. My only real complaint about the O11 Air Mini came after assembly: my 3.5" Hard Disk Drives were running hot and noisy. The included thin rubber drive grommets do very little to damp vibration. I was able to fit larger and softer silicone grommets on the side mount, and placing my 7200rpm drive on these made it a lot quieter. These larger grommets cannot be used on the rear trays as there is not enough clearance for them to slide in after mounting. The close mounting to the trays also restricts airflow, which brings me to the next problem.

In its full 7 slot configuration installing an ATX motherboard is possible.Fans can be mounted to the roof and there is space beside the motherboard to attach a radiator as well as a second radiator to the bottom of the case. Below are the full specification of Lian Li’s O11 Air Mini chassis. All models of this case ship with three fans, with two 140mm PWM fans at the front of the enclosure and a single 120mm fan in the rear. The case can support dual 120/140mm fans at the bottom of the case, and up to three 120mm fans and two 140mm fans at the top of the case. The O11 AIR MINI is ideal for air cooling builds, as it has enough clearance for up to 170mm for larger tower coolers. I absolutely love the this case to death after finally being able to build in a o11 based cased i have wanted to get forever and settled on the air mini since i have zero interest in custom water cooling and radiators which to me is a massive waste of time, money and hassle if anything breaks or leaks so i got this case solely for a Air cooled build and i love it so much i find my self just staring at how nice and tiny it is. Swapped all my parts out of a much larger and longer fractal meshify 2 since it took up to much desk space and was mostly empty so i love how compact and clean everything looks in a smaller case and my temps are far far better than what they were in a larger case with the ability to add more fans for airflow and im very surprised i was able to fit my large eatx motherboard in this with basically no real issues so you can in fact fit eatx up to a certain length as they mentioned and have it not affect your cable routing etc.The mesh design on the front, top and side panels of the O11 AIR MINI have been optimized to allow maximum airflow from different sides of the case to the temperatures stable and low. The super fine mesh also acts as dust filter to avoid dust buildup inside the case. Clearance for High-Performance CPU Cooler and ATX PSU Although O11 Air Mini is a compact case, it provides up to 167mm height CPU clearance, allowing users to mount their performance CPU cooler in the system.