With Pay in 3 - Interest Free and Pay in 12 payment plans, businesses can make those essential big purchases without blowing the budget - spreading payments over 3 or 12 months. If fault occurs due to overuse or misuse in high production areas, repair costs will not be covered by the warranty. This internationally acknowledged mark of quality means that this product is the result of efficiently coordinated development and production processes, technological expertise, continuous quality controls. Data protection: Please don’t include your own and other people’s addresses, telephone numbers or URLs or even the names of third parties (people as well as companies) in your review.

Might be enough grease on the the clamps already but just wondered what to use if i need to smear more on. Please remember we are here to help and if we can be of any further assistance at any stage please do not hesitate to contact us on 0117 244 4099. Dewalt would be top of the list as I already have some Dewalt and Facom stuff so the extra battery would be handy. I refer you to my earlier post on this topic - the grease is squeezed out until the metals make perfect contact, but the surrounding 'grease' makes a perfect seal arround it (more so than if it was just smeared on afterwards.Additional Grease Ease Dosing Solution, choose from either 25 litre or 10 litre (2 x 5 litre bottles) containers. Please note that general wear and tear over time and damage caused by neglect, misuse or incorrect use is not considered a manufacturing fault. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Prevents contact resistance from increasing during operation and provides lower loss than untreated contacts.

Instant, Maximum Benefit - When leasing you can invest in the best equipment for the job, even if business budgets do not allow for outright purchase. The TLGB 20 can deliver pressures up to 700 bar (10000 psi) and features a built-in light to illuminate the work area. These gases are released and contain an element of Sulphuric Acid which can corrode the connectors on the battery. I replaced the battery on my car (five year old Passat) recently and there was no sign of the terminals ever having been greased. NB: Do not spray directly onto the contacts as the grease has an isolating effect between the contact and conductor.If you DO have some corrosion, give it a good brushing with a wire brush till it is clean then coat with vaseline, making sure the nut and bolt are also coated. Features a 1/4" Hex drive shank that can be quickly attached to and operated by most battery drills or impact drivers as well as Main machines. It might be worth noting that another reason for smearing with this stuff is to prevent the battery leaking voltage across the terminals, especially when damp (look at your battery on a misty morning). We offer you the opportunity to rate products purchased from Louis and to share your experiences with them publicly. Milwaukee here too as have other things with the same batteries - the grease gun uses hardly anything.

After* you've made the connection you could smear a bit of vaseline over the terminals and connectors to keep the damp out, but if its a reasonably modern car there's prolly no need. The reason why battery terminals were greased was to protect them from the corrosive gases given off from unsealed batteries whilst they were charging. The reason I said this, is because in a car handbook(I've read all the books of all my previous cars), it recommends that you use petroleum jelly(exact words).However, if you would like to, you can change your settings at any time using the Change Cookie Settings link in the 'General Links' menu. etc, are all nigh-on perfect insulators - their purpose is not to improve the connection, but to prevent it deteriorating afterwards. The usage instructions are recommendations based on the tests we have conducted and on our experience; carry out your own tests before each application. The tool's display indicates battery charge level, amount of grease dispensed, pump/motor speed and blocked lubrication points. Any engineer charges incurred through a site visit, diagnosis and replacement of malfunctioning parts will also be covered.

Carefully clean battery terminals and clamps with a wire brush and connect battery according to manufacturer's instructions. The terminals and clamps should be clean when you make the connection - no oil, grease or anything else.Then coat battery terminals and clamps, particularly the screw connections, thinly with battery terminal grease.