I'm puzzled why the editors thought this was a good video to put up for viewing? It seems kind of like a discussion of how to make your own nails out of wire. Clean away all the broken plaster from the area above and remove any other debris. Vacuum the area as well to remove as much dust as possible. Wet the area with clean water and a brush then make up a slightly sloppy batch of bonding plaster. Trowel this out over the damaged area so that it bonds completely with the old plaster and completely covers the lathes. Once the sagging area of lathe and plaster has been re-supported like this, the recesses for each screw can be filled and the ceiling redecorated Larger areas of sagging ceiling Roll a special topcoat over the fiberglass mesh if you use the Nu-Wal product; otherwise skim coat the mesh with two coats of joint compound. Yes, I'd agee with the others. This is a decent tip for being in a pinch, but if you have an old house or work on them for others, you really ought to have a big bag of plaster washers. It's a whole lot less time consuming and they'll work better (bigger diameter, full of holes to key the skim plaster). I buy mine from Charles Street Supply (google) whose big quantity prices are a bit cheaper than Lee Valley. Seems like the Lee Valley price for 100 is good though.

Mark the line of the ceiling joists above and screw the plaster to these. Use dry lining screws with large washers on them. The washers will prevent the screw pulling right through the plaster and can be sunk a fraction into the surface. Dry lining screws will cut through easily and grip well in the joists. I use a Dremel tool with a diamond disk to make the the recess in the plaster to receive the washer. Be sure to use some sort of dust mitigation and wear a good dust mask, as this step can get messy. Secure the washers in the recesses with drywall screws. If the sagging is slight, or covers a small area, you can reattach the plaster to the wood lath by using long drywall screws fitted with plaster washers. A plaster washer is a thin metal disk that increases the size of the head of a drywall screw so that it doesn't pull through the plaster. You thread the drywall screw through a plaster washer and then drive it through the plaster and into the ceiling joists, wall studs, or wood lath. The screw and washer pull the loose plaster tight against the framing, restoring the ceiling. By surrounding the area with plaster washers, you can stabilize the plaster so that it doesn't sag any further. I would use those Plaster washers instead, larger in size and work better on my house with 100+ year old ceilings. This is usually a problem caused when the plaster has lost its key. I have lifted a ceiling up over 1" and then taped. It is no fun to remove 1.5" of old plaster on wood laths.If you look at the top side of a lathe and plaster ceiling you’ll see the lathes spanning across the joists. The plaster will have been trowelled onto the lathes so that it squeezed through the gaps and formed nibs. As it dried this will have formed a bond holding the plaster in place. This can get broken – most commonly in attics when work like boarding is carried out. Once damaged, the plaster below no longer has as much support from the lathes and can easily drop a little causing a bulge in the ceiling Small bulges in lathe and plaster

In older properties, lathe and plaster ceilings can become damaged and the bond between the old lathes and the plaster gets broken. Small areas can be repaired but larger areas are best cut out and replaced with plasterboard and then skimmed with finish plaster. First, locate the joists or studs and mark their location in the loose area. Push up the loose plaster and place 2-in. screws and the perforated plaster washers into the joists or studs about every 6 or 8 in. The convex washer will flatten as the screw tightens. If the plaster has a rough surface, you may need to first scrape the surface to get the washer to lie flat. Next, secure the loosened field to the lath between joists with more washers. Finally, skim-coat over the washers with drywall joint compound. It may take several coats and extra effort to create a smooth finish or mimic the existing texture. Trusted, comprehensive guidance for choosing, hanging, taping, sanding, and repairing drywall—the right way I'm puzzled why the editors thought this was a good video to put up for viewing? It seems kind of like a discussion of how to make your own nails out of wire.” You don't have permission to access "http://www.homedepot.com/p/Grip-Plate-Lath-and-Plaster-Washer-1000-Pieces-HDGPPWL1000/303868289" on this server.

Quick fixes for cracked plaster

Allow the plaster to dry overnight before gently removing the timber supports below. The ceiling can now be redecorated Substantial damage repair You now need to access the top side of the ceiling. For upstairs rooms, this is usually easy enough as you can get to it from the loft. For other ceilings, you will have to lift the floor in the room above to get access to the old lathes. I do appreciate the video however because you do preface it with "in a pinch", even though it's not a better way. I carry pipe strapping as well.

Install wallboard clips on the edges of the damaged wall by using the screws supplied with the clips. Save yourself time and trouble — make the patch a square or rectangle, even though the hole may be a different shape. Be sure to cut away any protruding paper facing or crumbled gypsum core from the perimeter of the patch area.Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration. It's been said by everyone else, Plaster Washers. I have a 100+ year old house and keep a supply on hand. I can only say this was a waste electrons for the video.