ONVIF push will result in slightly faster state changes of the binary motion/AI event sensors than ONVIF long polling. Not all camera models generate ONVIF push events for all event types, some binary sensors might, therefore, only be polled.

A822, ALL, Argus, Argus PT, B500, B820A, C1 PRO, c1pro, C1-Pro, C2 Pro, C2-Pro, D800, Duo, Duo 2, Duo 2 Wifi, E1 outdoor, E1 pro, e1 pro PTZ, E1 pro sub, E1 Zomm, E1 Zoom, Inside, Other, RCL-410, RCL-410-5MP, rcl-420, RCL-510WA, rcl-511, RCL-520, rcl-522, RCL-810A, REOLINK C2, Reolink RCL-410, REOLINK RLC-423, reolink: rlc-410-5mp, Reolink-820a, rlc 410w, RLC 482a, rlc 510, RLC 520, RLC 842, RLC-1220A, RLC-410, rlc-410-5mp, RLC-410-5MP, RLC-410W, RLC-410WS, RLC-411, RLC-411WS, RLC-420, rlc-420-5mp, RLC-420-5MP-V2, RLC-422, RLC-423, RLC-423WS, RLC-510A, RLC-510AW, RLC-510WA, RLC-511, RLC-520, RLC-520-5mp, rlc-520a, RLC-522, RLC-542WA, RLC-810, rlc-810a, rlc-810c, RLC-811A, RLC-812A, rlc-820a, rlc822a, RLC-822A, rls-410s, RTC-410, RWC-511, w511 All, C1, C1 Pro, C2, c2 pro, E1 pro, HIl, LivingRoom, Other, PTZ, RC410, Rcl 410, RCL-410, rcl-420, RCL-520, RCL-810A, Reolink RCL-410, reolink: rlc-410-5mp, rlc 411s, rlc 420, RLC-410, RLC-410-5MP, RLC-410S, RLC-410W, RLC-410WS, RLC-411, RLC-411S, rlc-411ws, RLC-411WS, RLC-420, rlc-420-5mp, RLC-422, rlc-422w, rlc423, RLC-423, RLC-423WS, RLC-510A, RLC-510A with substream, RLC-510WA, RLC-511, RLC-511W, RLC-520, RLC-520-5mp, rlc-520a, rlc-522, rlc-810a, RLC-WS423WS, rls-410, RWC-511, W410S Then power up the camera while pointing it at the QR code. It takes about a minute to initialize, read the QR code, and connect to your Wi-Fi. Showing the camera in the dashboard My RLC 520a is running the latest firmware 3.0.0.494 and I have also tried the previous version 3.0.0.250. After that you can disconnect the LAN cable and the camera will automatically switch to the Wi-Fi connection.This issue is related to the function of the camera itself, and it is indeed a temporary workaround solution so that your camera can maintain the synchronization of audio and video. Please install the waterproof lid at the junction of the Ethernet cable and the camera to protect the junction from water. To make the camera work, you need to use the PoE Switch (IEEE 802.3af, 48V Active) or DC Power (DC 12V1 /2A) to power on the camera. Unfortunately this does not always shows the latest available firmware (also not in the Reolink applications). Step 4. Once the camera is installed, you can adjust the angle up down 70 degrees or 360 degrees horizontally.

You may power on Reolink PoE cameras via PoE injector/switch or PoE NVR directly, or by using the power adapter.If an entity listed below has an asterisk (*) next to its name, it means it is disabled by default. To use such an entity, you must enable the entity first. Number entities Or if you want to make Reolink NVR work with the camera, its connection diagram will be like below: Guard set current position will set the current position as the new guard position. Select entities Normally, the digits are printed directly under the QR code. Alternatively, you could scan the QR code and grab the last 4 digits.

Floodlight turn on brightness controls the brightness of the floodlight when it is turned on internally by the camera (see Floodlight mode select entity) or when using the Floodlight light entity. After plugging the new camera to the NVR, the camera's image does not show up on the monitor and it prompts "video loss". The following troubleshooting may be helpful to you.

When the floodlight entity is ON always ON, when OFF controlled based on the internal camera floodlight mode (Off, Auto, Schedule), see the Floodlight mode select entity. Reolink UID (based on P2P) can be used for the set-up and remote access of Reolink cameras and NVRs. If you get Login failed/Connection failed/Timeout error message when trying to remotely access the camera via the UID, please follow this guide for a simple troubleshooting. (Please make sure you can log into your device on the LAN before the troubleshooting.) Connect your PoE camera to the PoE NVR by a single network cable, then the PoEcamera will get power via the PoE NVR.

When IR light entity is OFF always OFF, when ON IR LEDs will be on when the camera is in night vision mode, see the Day night mode select entity. Sensor entities Follow the on-screen instructions to first setup the credentials (use the same credentials in Home Assistant). Please note that the optimum distance between the camera and the PoE switch/Reolink NVR is 300 feet.E1 pro, e1 pro PTZ, E1 Zoom, Other, RCL-520, reolink: rlc-410-5mp, RLC 423, RLC 482A, rlc-410-5mp, RLC-423, RLC-510A, RLC-520-5mp, rlc-522, RLC-810A, RLC-811A, rlc-820a, RLC-823a, RLC-842A, Video Doorbell PoE However I discovered that the sound and audio were gradually drifting out of sync - up to about 4 seconds apart. The video is lagging behind the audio. This means that not only is the recording out of sync but also the snapshot starts to miss the event due to the video lagging. If I disable and re-enable the camera in SSS it is all great again but then the drift starts again.