Additionally, This is also where the PSU and storage are concealed. The main chamber will display your best components and this case makes cable management a breeze. Corsair Dominator Titanium First Edition DDR5-6600 C32 2x32GB Review: Abundant Capacity And Performance The bottom of the case even has a removable dust filter for easy cleaning. There is plenty of room for enthusiast-grade hardware in both air and AIO cooling setups. There are even several different configurations depending on your preferences. This versatility allows for up to 280mm radiators, large GPUs, tall CPU coolers and ATX motherboards. Constructed of steel instead of aluminium, the O11 Air Mini no longer retains the initial focus on ITX builds, evident in the case's larger footprint. The undesirable feature of the unattractive bottom air filter is unfortunately still here. Despite these changes, the case has kept its cost reasonable, while its size remains relatively compact for an ATX case. A sophisticated profile is crafted through the steel mesh panel at the front, a change from the lively look of the Lian Li O11D Dynamic Mini’s glass side and front panel. However, the see-through side panel and the aluminium trim accent at the front remain. Configuration Options

The second side panel is closed with an aluminum mesh panel. The two mesh strips sit directly above the PSU and HDD slots, as well as directly above the fan mount on the partition between the two chambers. In the event that fans are installed there, they will get enough air.Clearance for High-Performance CPU Cooler and ATX PSU Although O11 Air Mini is a compact case, it provides up to 167mm height CPU clearance, allowing users to mount their performance CPU cooler in the system. Inside, as already mentioned, the well-known and proven two-chamber system is used. Here, the two chambers are separated by a wall that forms a “step”. In this step you can install a 240 mm radiator. In the bend of the partition are two openings, which are provided with gray rubber lips. Cables can be cleverly passed through here without opening the view into the second rear chamber. If time is saved on perfect cable management, this still keeps things looking tidy in the visible main chamber. The power supply is mounted in the Lian Li O11 Air Mini as usual with four screws. Well thought-out by Lian Li: The power supply is slightly elevated and does not rest on the floor. This gives you the opportunity to neatly run cables underneath and thus reach the lower slots on the motherboard. Similar openings are also found on the upper edge. In the HDD/SSD case, the disks can be stored in two holders with the included screws. Once screwed tight, they can be put into the case. Practical test

the O11D Mini is designed to support a maximum number of radiators to optimize the water-cooling potential, Small tower with big airflow, the O11 AIR MINI provides modular design for ATX, M-ATX or ITX motherboards. Being all about the air, O11 AIR MINI has a spacious interior to accommodate multiple confirgurations of fan and radiator setups to maximize the airflow. Please note that whilst we endeavour to provide information as accurately as possible, there are times when components may be cosmetically different than shown due to new revisions of hardware.In this main compartment, CPU coolers can be up to 6.6 inches (167mm) tall and GPUs up to 14.3 inches (362mm) long. In the condition of using the included riser cable (PCIE3.0) of the vertical GPU kit with a PCIE 4.0 motherboard and a PCIE 4.0 GPU, please follow bellow steps to set up your BIOS to make it compatible.

The installation of the components went very well. All important places were easily accessible, which is also due to the easily removable side panels. As soon as the lid was loosened, the front and side could already be removed. The well-known from-above-insertion principle of Lian Li found its way here, too, of course. Our team of specialists would be more than happy to assist in choosing the right system for you and to discuss upgrades or technical advice should an issue arise. The VGA-Vertical Bottom Mode gives only 20mm clearance and does not allow for fan or radiator installation. With any motherboard it does not allow fan or radiator support in the bottom. Lian Li O11 Air Mini supports a motherboard up to E-ATX, however it is much more interesting when you work with a smaller Micro-ATX as that allows you to open up the top of the case for cooling hardware. Microsoft for Business CouponExclusive: 20% off select Surface Pro 9 for Business + Type Cover BundleThe O11 AIR MINI comes with 2 x 140mm PWM front fans and 1 x 120mm PWM rear fan pre-installed straight out of the box. Get your system up and running faster with ease. The 5 Slot Mode is ideal for ITX and M-ATX motherboards and allows up to 280mm radiators to be installed at the top. If using a M-ATX motherboard, the bottom radiator can only be 240mm, but with ITX you can install up to a 280mm radiator. If you haven’t spotted it yet, I’ve made a mistake in my build process. Although the 240mm radiator fits, with the fans, entirely into the side slot in the main chamber without colliding with the included intake fans, this is not the best way to mount it as it wouldn’t effectively exhaust the air out the side, instead warming up the secondary chamber. Each PC also undergoes high level configuration and optimisation for high-end applications such as: