Maximum Acceleration: it means the maximum acceleration of the motion axis in accelerated or decelerated motion. If the acceleration is set too large, it will make the motor lose steps, jar and even squeak; if too small, it will cause the reduction of acceleration so as to reduce the running speed of the whole figure. For the axis with larger inertia, such as Y axis corresponding to the beam, its typical setting range is 800~3000mm/s2; for the axis with smaller inertia, such as X axis corresponding to the car, its typical setting range is 8000~20000mm/s2. If we take a look at where these wires go to, you’ll see that some of these go to the motor driver X and the motor X, the driver Y and the motor Y. A step pulse is a transition from low to high, or high to low. The controller will hold the line low, and pulse it high, or hold the line high, and pulse it low. The transition itself is what matters, and motor drivers will either look for a transition from low to high (rising edge) or high to low (falling edge) to accept as a ‘Step’.

If we take a look at the top left hand corner there, we should see that the main’s comes into a filter. Focus Setting: it means the distance from the focal point of laser head lens to Z-axle origin. When there is no automatic focusing function, this parameter becomes invalid. Laser Tube Enable: when there are double laser tubes, user can enable laser 1 and laser 2 respectively.Import artwork in a variety of common vector graphic and image formats(including Al.PDF, SVG, DXF, PLT, PNG, JPG, GIF, and BMP)

All outputs are isolated through the optocoupler, and 500mA current for each, OC gate output, each can directly drive the 6V/24V relay. So the controller I have is Ruida RDC6442S-B(EC) I found one other thread talking about this but it didn’t seem to go anywhere.Idle Move Speed: this parameter decides the highest speed of all non-lighting lines for the machine in the movement process. there are a set of legends here which are numbered one to 15, which tells you exactly what these LEDs do.

Easy-to-use software: The software should be user-friendly and intuitive to operate, with clear and concise instructions.Ruida Controller is a series of motion control systems used in laser engraving and cutting machines. It provides high-speed and precise control of the laser head for cutting and engraving various materials such as wood, acrylic, leather, and metal. The Ruida controller is known for its reliability and ease of use, and it is compatible with several software programs such as RDWorks, LaserCut, and LightBurn. Push “Z/U” key to move the changing item, then push “X+/-” keys and “Y+/-” keys to change the value, when all the IP value and the Gateway value are changed, push “Enter” key to validate the change, or “Esc” key to invalidate the change. Diagnoses Laser Type: glass tube, RF laser (not need pre-ignition pulse) and RF laser (need pre-ignition pulse) are available for option. Basically, just like you do on your spark plug for your car, in a slightly more sophisticated manner. After-feeding delay: settable at 0~9.9s. It can facilitate the feeding device’s delaying vibrated after moving to the correct position and waiting for the 2nd work after the feeding axle stands still completely.

When showing this menu, the system would read the memory file firstly, the file name and the work times would be listed in the area, and the selected file is previewed in the bottom right area. “Y+/-” keys could be used to move the cursor on the file name list. When the cursor is on a target file name, presses the “Enter” key, the selected file will be previewed on the main interface, and then if “Esc” key is pushed, the preview will disappear.DSP (Digital Signal Processor) Technology: The DSP technology employed in the Ruida controller enables high-speed processing and precise control over laser parameters, resulting in exceptional cut quality and intricate engraving details. Both the DRC6445S and DRC6445G support multiple communication protocols and are compatible with a range of laser cutting and engraving machines. The choice between the two would depend on the user’s specific requirements and the level of complexity they need in their laser control system. Size