Lightweight Access Branch manufactured from uPVC for strength and durability. Easy to work with and suitable for high temperature waste discharges. Access branch enables testing and maintenance of the soil system. The use of silicone lubricant on all seals will facilitate jointing. For use with 32 and 40mm boss adaptors. A more modern alternative solution to the pressure problem is to install an Air Admittance Valve instead of a vent pipe. Sometimes known as Durgo Valves, Air Admittance Valves (or AAV's for short) are essentially one-way valves that can be installed at the top of the soil pipe, or along a waste pipe run, to allow the free entry of air into the pipework system to balance out the pressure. The design of these valves is quite clever, as they only open when the siphoning pressure (the negative pressure caused when water flows into the pipes) builds up enough to require balancing, and only in a way that allows clean air to be drawn in without allowing foul air to escape. This is the crucial difference between the valve and the vent. A waste system, as previously mentioned, is made up of pipes and fittings designed to carry wastewater from sinks, showers, bathtubs, washing machines, and dishwashers out to the sewer. Because these pipes shouldn't have to carry any solid waste away (stop scraping leftover food down the kitchen sink!), they don't need to be as large a diameter as the soil system pipes, meaning that less space is required to install them. The most common waste pipe sizes in the UK are 32mm (suitable for low volume outlets, such as small hand basins), 40mm (suitable for most kitchen sinks, showers, and baths), and 50mm (suitable for more commercial applications, or for connecting multiple waste pipes into a single flow. Colour matching between systems facilitates colour coordination where sanitary pipework is located externally.

Pipes | 110mm Underground Soil Pipes | Toolstation Drainage Pipes | 110mm Underground Soil Pipes | Toolstation

Traditionally, most waste pipes used to be made from either copper, iron, or lead, and many properties may still have systems that are at least partially comprised of these materials. Copper is actually still quite popular today, among some professionals, as the pipes can be made to fit into tighter spaces, are more flexible at the joints (therefore offer good resistance to vibration damage), and have a certain premium aesthetic appeal. The more modern alternative to copper waste pipes, however, is plastic. Each have their own pro's and con's, but the popularity of plastic pipes has grown exponentially due to the fact that they are much less expensive than copper pipes, easier to install, more resistant to corrosion and impact damage, and quieter at high pressure and water speeds.Conversion Bends - used to create changes in direction while also converting the connection type between push-fit and solvent weld.

soil pipe and waste pipe systems | JDP A basic guide to soil pipe and waste pipe systems | JDP

Compatible with most other existing materials and systems manufactured to British/European Standards. Note: If your property uses a sewage treatment plant, septic tank, or cesspool instead of a connection to the mains drains, there must be AT LEAST one open vent in the system to prevent a dangerous build-up of gasses. Solving pressure build-up with an Air Admittance Valve Hiding within the walls and under the floors of your home, there are many different types of pipes coming and going. Some supply you with clean water, and others take away the waste so you don't have to worry about it. While the difference between water pipes and wastewater pipes is quite clear, the difference between soil pipes and waste pipes can be a bit murkier. Soil pipes also need to be larger in diameter than waste pipes on the account of having to handle more…solid materials. While having your sink drain into a soil pipe wouldn't really matter much (apart from using up an unnecessary amount of space under it), having your toilet drain into a waste pipe would be a recipe for a very unpleasant disaster in your home. Bodily waste produces methane and other unpleasant/dangerous gasses that must be vented out of the system before reaching the sewer. For this reason, soil pipe systems are typically designed to be vented through the roof of your home to allow the gasses to escape out into the air. The wastewater produced by washing your hands, having a shower, washing your clothes, or doing the dishes doesn't produce these gasses however, therefore waste pipe systems don't require this ventilation.This vent allows air to be drawn in from outside the property to rebalance the pressure in the system rather than from internal sources, thus avoiding the siphoning effect. As previously mentioned, a vent pipes other function is to allow soil system gasses to safely escape out into the atmosphere. For this reason, a vent must, according to building regulations, always terminate above the roofline of the property and be at least 900mm higher than any window or opening that is within 3 meters of the pipe. Tees - used to connect two waste pipes (single Tee) or three waste pipes (Cross Tee) together at a 92.5-degree angle.