They should be huge and I mean HUGE! Pattern your favourite shorts, triple all the measurements. Take into account that we need extra fabric since we're going to be raising our bloomers later on when the elastic bands are attached, to create the folds and puffiness under the skirt.

Shoes | Multicolour | Vans Vans X It Era Shoes | Multicolour | Vans

You'll Float Too Halloween 2 Sided Hoodie/Sweatshirt,Scary Halloween Sweatshirt,Horror Character Sweater,Horror Clown Balloon Shirt,IT Movie For attaching the strips on, we are going to need a 25cm long rectangular piece by 29cm width, this will be our sleeve. Once your pompoms are nicely glued you can start trimming off the excess to make them less fluffy and more like the reference For the individual bands attached to the pants we're going to be making 2.5 cm high by 39cm wide strips. Don't forget to add an extra and a half cm on top so we can fold and sew as well as have 1cm under each strip so each strip can overlap nice and evenly. We also need to add 5mm under our strips for seam allowance, to fold, iron and have neat clean edges that show. So for the pants we are going to be needing 12 panels that are 5cm high by 39cm wide You'll Float Too Sweatshirt, IT Movie Shirt, Pennywise Georgie Shirt, Halloween Horror Movie Shirt, Spooky Season Shirt,Pants cuffs are 36cm circumference and 12cm high, inner pants cuffs are 36cm circumference and 15cm high Just measure the circumference of your abdomen and make the fabric long enough to include press on buttons as well later. The shoes of pennywise looks like custom-made old-school boxer shoes. Its very fun and easy to modify old shoes with some craft leather, vinyl, here’s how: I drew my collar measurements on a piece of newspaper to test and pin it on my shirt, I highly recommend this method. Leaving the last big pyramid to come out more than our strip of fabric, and fold the two side pyramids to have a flat bottom, this way we have that nice pointy tail at the end.

Pennywise shoes - Etsy

For the circumference of the bottom gathers, Measure the circumference of your elbow when you fully bend it and add 2 cm to that. My elbow is 27cm so the bottom gather is 29cm. Once you've got the correct measurement after gathering, make a knot with the two ends of the string to secure your gathers. Cut a flat piece of fabric to the same length from the collar seam down to the bottom of the skirt (55cm long by 9cm wide, don't forget to add extra for seam allowance)Height-wise, Measure from under your ribcage down to your knees to get the length, 60cm for me. Add 3cm extra up and down to have room for the elastic bands. If your shoe size beyong 26cm(Women EU size 41,Women US size 10),the High Heel design has to be removed due to the quality concern. Then we're going to carefully trim the excess with the xacto knife being cautious to not cut the shoe but just above the sole.

Penny Wise Mask - Etsy UK Penny Wise Mask - Etsy UK

Now you can take fun pictures and impress your friends and family with your costume, please be responsible and don't make it too scary for your peers, this costume is meant for fun. I had a great time creating it :) Vintage Pennywise Horror Movie Fall T-Shirt, Penny Wise Killer Comic, IT Movie Halloween Shirt, Horror Character Shirt, IT Movie Sweatshirt Once this is done and you have both sleeves pieces with the 8 strips attached you can go ahead and sew these sleeves closed The ropes I bought are of 2mm diameter, I got them from etsy: https://www.etsy.com/listing/728725039/2mm-satin-c...

Start of by ironing and sewing the edge that will show on all 8 of our strips (16 strips in total, 8 for each arm) so it looks nice and neat The height of this strip should be 5 cm so that our collar will measure 3cm in the end. The extra cm is again for seam allowance. The outer cuffs should be 12cm high and 28cm wide and the inner cuff with the pleated fabric, should be 15cm high and 28cm wide. We’re going to add a fabric channel inside the sleeve to hold an elastic band, which tightens nicely around our biceps, to give our sleeve a puffy form. The elastic I am using is of 7mm height. Cut and spread/distribute out the template pieces so the outer pieces edge to edge make 80cm. I leave 8cm gap between them, trace the top shape of the template, draw the bottom edge acording to the length we want (39cm) and add seam allowance too.