You can fill small gaps around pipework with silicone fillers, similar to the fillers used for skirting boards and floorboards. Fill larger gaps with expanding polyurethane foam. This is sprayed into the gap, expands as it dries, and sets hard. We have more information about insulating tanks, pipework and radiators. Draught-proofing external doors can stop a lot of heat from escaping, and won’t cost you much. There are four main areas to consider draught-proofing: When you've just got in and shrugged off your heated gilet, the last thing you want is to have to sit in a chilly room. This hard-wearing fabric design from John Lewis will not only keep out the draughts under your internal doors, but it also offers a neutral and modern look that won’t look out of place in a stylish living space.

Draught Proofing: 11 Ways to Eliminate Draughts | Homebuilding Draught Proofing: 11 Ways to Eliminate Draughts | Homebuilding

The difference between draughts and ventilation is one of control. Draughts are uncontrolled, while ventilation is ours to switch on and off at will. Home ventilation in the form of extractor fans and cooker hoods will ensure that condensation is properly dealt with, at source.

DraughtEx Skirting Board Installation Video

All homes need some ventilation but the difference between ventilation and draughts is that ventilation is a flow of air that is controlled. Draughts are gusts of cold air where you don’t want them. Cold air flowing in from either the outside, or an unheated area of the house will cause you to feel cold and turn your heating up. This in turn costs you more money and is bad for the environment. Where do the draughts come from?

Floorboard Insulation by Draughtex - Low Energy Supermarket Floorboard Insulation by Draughtex - Low Energy Supermarket

For sliding sash windows, foam strips do not work well. It’s best to fit brush strips or consult a professional. For windows that don’t open, use a silicone sealant. If you’re thinking of replacing your windows, consider installing energy efficient windows. Moving in 2002 to a small-holding in South Wales, providing as it did access to a wider range of natural resources, fanned his enthusiasm for sustainability. He went on to install renewable technology at the property, including biomass boiler and wind turbine. Nothing will give you a better sense of whether something is worth buying and is cost-effective than an honest, unbiased review from a real parent. That’s why our first port of call is always the Mumsnet forums where we trawl the Talk boards to seek out recommendations and top tips from the Mumsnet community. Expert opinionsIf it is not used then get the chimney sealed (in this case a professional will be needed) top and bottom. Controlled ventilation helps reduce condensation and damp, by letting fresh air in when needed. However, draughts are uncontrolled: they let in too much cold air and waste too much heat.

Draughtex Floorboard Skirting Board Insulation Floor Gap Draughtex Floorboard Skirting Board Insulation Floor Gap

This will largely depend on the type of draught excluder you’re using. Fabric excluders don’t require any fitting unless you want to hook it to your door, in which case you’ll need to hammer in a couple of nails to attach it. Some of the strip options come pre-glued, whilst others will need screwing onto the door. Can you paint over your draught excluder?Remember to remove the draught-proofing if you decide to light a fire. Find out more about draught-proofing your chimney.

Cutting out draughts from older homes - Energy Saving Trust Cutting out draughts from older homes - Energy Saving Trust

A 12 x 12ft room has approximately 25 floorboards and an average gap area of 3.87ft which is similar to a small window being left open. DraughtEx Thin has a profile of 4mm and is suitable for skirting board gaps less than 3mm - More Information.DraughtEx Standard has a profile of 8mm and is suitable for skirting board gaps between 2 and 7mm - More Information.