Decide where you will install the hook. Grab the stud finder to locate a joist in that area. Don’t have a stud finder, try one of these 5 Ways to Find a Stud without a Stud Finder. Make several passes to ensure you know exactly where the joist begins and ends, and mark the area accordingly. Step 2 Using a 3/8″ drill bit and drill, make a larger hole into the ceiling drywall to fit the end of the toggle bolt. Step 4 Drill a small pilot hole into the drywall and joist with a drill bit slightly smaller than the size of the screw being used. I have always had the “make it myself” attitude and I’m not afraid to bust out the power tools or get creative when it comes to decorating our home on a budget. You can usually find me scouring the local thrift stores, garage sales and estate sales looking for my next makeover (like this litter box cabinet), or dreaming up ways to make our new house feel more like home. My most recent project was giving my home office a much needed facelift. Some of the plans included creating a fun inspirational accent wall and adding pegboard to store my craft hoards. Take particular care to drill accurately sized holes when using poly or nylon toggles. Plastic or nylon poly toggles are suitable for light to medium loads such as lighting fixtures. Poly-toggles or nylon toggles work in a similar way to the plastic expanding anchors above. Metal Spring Toggle

Hook M4/90mm Wall Mounting Ceiling Hook Wing Spring Toggle Hook M4/90mm Wall Mounting Ceiling Hook

Hanging a plant hook using a ceiling joist is the most secure way and the safest, especially if you plan to hang a heavy planter. Materials: Locate the nearest ceiling joist where you want to hang your hook. A joist is one of the beams that supports a ceiling, and it's the securest place to fasten a hook. The easiest way to locate your ceiling joists is by using a stud finder [2] X Expert Source Gino Colucci I’m Amanda, and I am the creator and voice behind the food and DIY blog, Domestically Creative. What started as a place to share updates with friends and family after we moved from Illinois to Tennessee and then to Texas, turned into a passion for finding creative and frugal ways to feed us and decorate our homes.These relatively new plasterboard fixings are available in a variety of colours, each capable of holding different maximum weights. These range from blue (113kg) to yellow (71kg). GripIt fixings work by having three separate loading points, dispersing the weight of the object being held better than many traditional fixings. They are only really suitable for use in places where they will be hidden behind the fixture. A large hole needs to be drilled, and the GripIt sits flush at the edge and is clearly visible. You can find out more about GripIt fixings here. Decide where you’ll be installing the ceiling hook for your plant and make a small mark with a pencil. Step 2

drywall ceiling? How much weight can I hang from a drywall ceiling?

H and screw the hook into place until it is flush against the drywall. (If it becomes too difficult to turn, you can put a screwdriver into the hook to use for leverage.) These plastic or Nylon fixings are squeezed flat and slotted into a pre-drilled hole. Once inside, the flattened end opens out to act as the anchor. The screw then pulls the two flaps or wings flat against the inner face of the plasterboard to fix it in place. When attached, simply bring the board up and along until the clamps align and clip together. The plasterboard can then be gently pushed (hinged) upwards and is it automatically square with the joists. A neat and strong, all-in-one plasterboard fixing. These are available in a variety of types, with standard screw heads, as well as hooks and loops. This makes them good for hanging things from a plasterboard ceiling. They are also available in a range of sizes. A hole is drilled that matches the width of the unexpanded plastic sheath. The expanding anchor is pushed all the way into the hole and then tightened by turning the screw, hook, or loop. As the screw tightens, the plastic sheath spreads until it is tightly pulled against the inside face of the plasterboard.You can also use earth magnets to find the location of the screws in the studs. [3] X Expert Source Gino Colucci

Ceiling Board Hanger - The best way to install plasterboards

All plasterboard fixings are designed to do basically the same thing: Increase the area of the plasterboard which is put under stress by the object hanging from it. However, not all of them do this in the same way and not all of them are suitable for all applications. As a general rule, use plastic or metal screw in fixings for light loads, plastic anchor or spring toggles for medium loads, and metal spring toggles for heavy loads. Plastic Expanding Anchors If you have a crawl space or an attic with exposed joists, look to see which direction the joists are laid and also how far apart they're spaced.

Metal spring toggles offer the best support for hanging on a plasterboard wall. The metal toggle is squeezed flat and pushed through the drilled hole in the plasterboard. Once it is behind the plasterboard, the toggle springs open and the two wings pull flat against the inside face. As the supplied machine screw is tightened, the wings are pulled tight against the inside face and spread the weight of the load. These plastic plugs are not much different from standard wall plugs, except that they are generally shorter and wider, and they spread more when the fixing screw is inserted and tightened. Cheap and easy to use, but only suitable for light loads. As with a normal wall plug, a hole of the correct size needs to be drilled into the plaster (slightly smaller than the plug) before the plug is inserted. Poly-Toggle or Nylon Toggle Holding the wings on the toggle bolt closed, gently insert the bolt (hinge side first) into the hole in the ceiling drywall. Cavity fixings work in a similar way to plastic or poly toggles. They are pushed into a pre-drilled hole and then the action of the machine screw turning in the fixing spreads four wings outwards to grip against the inside face of the plasterboard. Most cavity fixings have a toothed flange to grip the outer surface of the plasterboard. This needs to be pressed firmly into the surface of the plasterboard to stop the fixing turning as it is tightened.

Ceiling Hooks, M5x90mm, Carbon Steel Wing QWORK® 12 Piece Ceiling Hooks, M5x90mm, Carbon Steel Wing

Get over 16000 woodworking plans. Learn how to build anything from furniture to birdhouses out of wood. Clear and detailed plans that guide you through the process of each project step-by-step. Fixing to Dry-Lined Walls The clamps will allow one person to hold and align the panels in position – saving on expensive double-labour costs associated with this type of work.If you don’t want to go through the trouble of finding a joist, or there isn’t a joist where you want to hang your plant, you can use a toggle bolt with the hook. (Just make sure your plant isn’t heavier than the specified weight limit for your ceiling hook.) It sounds intimidating, but it’s actually very easy! Plasterboard Fixings– When hanging anything heavy from a plasterboard wall, it is always better to use more fixings than you might normally need. Using four plasterboard fixings instead of, say, two fixings, will greatly help to spread the load of the wall unit, shelf, etc, and therefore reduce the chance of the fixings pulling out of the wall. These plasterboard screws combine a metal or nylon plug with a screw thread for the fixing screw. They vary in size and length but they all have the deep outer thread in common. The deep thread is designed to give a much better grip on the plasterboard, whilst also spreading the weight of the object they are holding up. Suitable for light loads and plasterboard in good condition. Plasterboard Plug When using spring toggles, you will need to remove the spring part from the machine screw and then pass the screw through whatever you are fixing (cabinet, etc) before re-attaching the spring toggle and pushing it into the hole in the plasterboard.