Also exist screwless carburetors, responsible for the enrichment of the combustible mixture at low speeds. That is, they have only 2 adjusting screws: the idle speed regulator and the fuel mixture quality regulator at high speeds. You can learn how to tune this type of carburetor from this video.

Stihl FS45, FS55 Brushcutters - OEM Carburettor C1Q-S265 for Stihl FS45, FS55 Brushcutters - OEM

The acceleration of the air flow contributes to the transfer of fuel (gasoline) and its atomization. Ultimately, an air-fuel mixture of the desired proportion or density appears. Base carburetor lawn mowers. duralumin housing. It contains a diffuser (a hole with internal contours). Air is blown through this hole. The oxygen (air) flow rate depends on the cross-section (passage opening) of the diffuser. Thus, using 3 adjusting screws, it is possible to achieve maximum engine performance, as well as to configure its smooth operation at any ambient temperature, and even in mountainous areas. Common carburetor malfunctionsBefore adjusting, you must carefully clean the filters according to the maintenance in the annotation. Read:

Stihl FS55R Petrol Strimmer / Brushcutter | Mowers2Go™ Garden Stihl FS55R Petrol Strimmer / Brushcutter | Mowers2Go™ Garden

The valve (14) by means of a lever (17) is connected to the membrane (18). The cavity, which is located below the membrane, is connected to the atmospheric air through the hole (19).The standard cutter that comes with the Stihl Stimmer FS 55 R is the AutoCut 25-2. Features We Like Electronic ignition module Important! If the engine is allowed to run at full speed for more than 10 seconds, then it may fail.

Stihl FS55, HL45, HS74, KM55 Carburettor - C1Q-S66 - WT264

FC55, FC75, FC85, FS38, FS45, FS46, FS55, FS75, FS80, FS85, HL45, HS72, HS74, HS76, HS80, HS85, HT70, HT75, KM55 A common malfunction that “chases” the fuel pump is pump membrane deformation. For this reason, it does not fit properly and the pump channels are not sealed. Left knob H responsible for the enrichment of the combustible mixture at high speeds. The enrichment setting completes the carburetor adjustment. Also, using this controller, you can adjust the maximum speed, fuel consumption and engine power. The loop handled grass trimmers and brushcutters are ideal for working in areas where space is limited, e.g. thinning between bushes and shrubs. Multi-function control handleSimply put, adjusting the carburetor on the lawn mower is creating the optimal fuel mixture due to the correct air supply. how adjust lawn mowing carburetor

CARBURETOR For STIHLFS38 FS45 FS46 FS55 T FC55 - Farmertec CARBURETOR For STIHLFS38 FS45 FS46 FS55 T FC55 - Farmertec

It is curious that, based on the beliefs of the creator of the video, the setting (its correctness) is determined by the color of the candle, and not just by the speed and stability of the motor. Strainer How to adjust the chainsaw How to properly adjust the carburetor on the husqvarna chainsaw. There are only two obstacles with this element: If dirt accumulates in the adjustment cavity, the inlet needle cannot close the hole tightly and a lot of fuel is poured into the chamber. The FS55R is another great product from Stihl, not as noisy as expected but still very powerful. Easy to handle if you are a beginner.Stihl has designed the FS 55R brushcutter with the traditional grip combination; one hand at the motor, the other at the loop hold further down. With the added over the should harness, you can use the trimmer for extended periods of time. What’s more, it offers better support for a flowing strimming action Due to hit poorly cleaned air, The shaft wears out and may break. Broken parts of the shaft can enter the combustion chamber or crankcase and cause serious damage to the entire piston system. Pulse channel (1) connects the impulse chamber of the pump to the crankcase, namely, to its internal volume. The piston located in the cylinder, making a reciprocating motion, successively changes the pressure in the crankcase (vacuum or pressure increase). Pressure drops make the membrane move (4). Therefore, the operation of the pump is synchronized with the operation of the engine.