The Cisco 10GBASE-ER module supports a link length of up to 40 kilometers on SMF (G.652). SFP-10G-ER-S does not support FCoE. The Cisco 10GBASE-LRM Module supports link lengths of 220m on standard Fiber Distributed Data Interface (FDDI) grade Multimode Fiber (MMF). To make sure that specifications are met over FDDI-grade, OM1 and OM2 fibers, the transmitter should be coupled through a mode conditioning patch cord. No mode conditioning patch cord is required for applications over OM3 or OM4. For additional information on mode conditioning patch cord requirements please see: https://www.cisco.com/en/US/prod/collateral/modules/ps5455/product_bulletin_c25-530836.html.

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla. Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door bevoegd geschoold personeel.Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. The primary difference is how light is transmitted through the two fiber types. Single-mode uses a single relatively straight beam of light, transmitted directly through a core of glass (or occasionally plastic) that's usually 50 microns across. Single-mode accommodates large power levels, and is almost exclusively used for Long Range (LR) applications. set baseFontWeight = "normal" %} /* More than likely, you will use one of these values (higher = bolder): 300, 400, 700, 900 */ The SFP and SFP+ formats are a wonderful invention, allowing a single piece of hardware - like a switch or firewall - to accommodate a wide variety of cable and connection types, simply by swapping out the connector being used. Unfortunately, this also means that finding the rightSFP/SFP+ transceiver for your application can sometimes be confusing and difficult, because of just how many connection types exist. The Cisco 10GBASE-ER Module supports a link length of up to 40 kilometers on standard Single-Mode Fiber (SMF, G.652).

Note: Parameters are specified over temperature and at end of life unless otherwise noted. When shorter distances of single-mode fiber are used (<40km), an inline optical attenuator must be used to avoid overloading and damaging the receiver. set headerType = "fixed" %} /* To make this a fixed header, change the value to "fixed" - otherwise, set it to "static" */ Cisco 1000BASE-LX/LH SFP transceiver module for MMF and SMF, 1300-nm wavelength, extended operating temperature range.A SFP-10G-BX40D-I device is always connected to a SFP-10G-BX40U-I device with a single strand of standard SMF with an operating transmission range up to 40 km. The Cisco 10GBASE-SR Module supports a link length of 26m on standard Fiber Distributed Data Interface (FDDI)-grade Multimode Fiber (MMF). Using 2000MHz *km MMF (OM3), up to 300m link lengths are possible. Using 4700MHz *km MMF (OM4), up to 400m link lengths are possible.

The SFP-10G-ZR-I has a cold start at -40 ⁰ C, the transceiver will be operational except optical traffic is not supported from -40 ⁰ C to -28 ⁰ C, all other low speed features (DOM, I2C, etc.) are operational. The module is fully operational -28 ⁰ C to 85 ⁰ C. By comparison, standard transceivers are generally restricted to operating temperatures from about 0°C to 70°C (32°Fto 158°F). For S-Class SFP+ 10 Gigabit Modules, refer to the link below: https://www.cisco.com/c/en/us/products/interfaces-modules/transceiver-modules/datasheet-listing.html. The Cisco SFP-10G-ZR-I is a multirate 10GBASE-ZR, 10GBASE-ZW, and OTU2/OTU2e module for industrial operating temperature range. The SFP-10G-ZR-I has a limiting electrical interface receiver, which does not require EDC PHY on the host board, it can be plugged into any SFP+ port. It supports link lengths of up to 70 kilometers on standard Single-Mode Fiber (SMF, G.652), assuming a fiber chromatic dispersion of 20ps/(nm *km). This interface is not specified as part of the 10 Gigabit Ethernet standard and is instead built according to Cisco specifications. The SFP-10G-ZR-I has a cold start at -40⁰C; the transceiver will be operational except optical traffic is not supported from -40⁰ to -28⁰C, all other low speed features (DOM, I2C, etc.) are operational. The module is fully operational from -28⁰C to 85⁰C. Choose Hummingbird Networks and save money! Our own Hummingbird-brand transceivers are 100% compatible and truly no different aside from the name on the casing. How do we do it? Because other name-brand transceivers are incredibly overpriced, relative to production costs. It truly is that simple.

Receiver Sensitivity specified over 1530-1565nm only, with 3dB degradation permitted from 1260-1530nm The Cisco 10GBASE-LR Module supports a link length of 10 kilometers on standard Single-Mode Fiber (SMF, G.652). Cisco 1000BASE-EX SFP transceiver module for SMF, 1310-nm wavelength, extended operating temperature range. The Cisco 10GBASE-ER Industrial Temperature Module supports a link length of up to 40 kilometers on standard Single-Mode Fiber (SMF, G.652). The SFP-10G-ER-I for Industrial Operating Temperature Range is a multirate 10GBASE-ER, 10GBASE-EW and OTU2/2e module. The SFP-10G-BXD-I and SFP-10G-BXU-I SFPs also support Digital Optical Monitoring (DOM) functions according to the industry-standard SFF-8472 Multisource Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage.