If you're planning to run the floor through the doorway without a break, you will need to cut the door linings and architraves all the way round both door jambs but if you're stopping at the doorway, just cut the linings as far as you're taking the floor. Don't forget to allow the same expansion gap around pipes and columns. The easiest way to drill the holes in the floor for radiator pipes is shown in the diagrams above. Line up the floor so that the header joint between two boards is in line with the pipe, join the boards together and mark where the hole should be. Drill the hole, take the boards apart and then slot them together around the pipe. You can then use a radiator pipe coverto cover up the expansion gap. If for some reason you have to switch the underfloor heating off, you must carry out the above process in reverse.

LiViT LVT is not suitable for outdoor use or conservatories. Ensure that the indoor temperature is always kept above 5°C and ideally between 18 and 25°C. Avoid long-lasting exposure to direct sunlight . Use felt pads under furniture legs to stop any unforeseen scratching and put castor cups under the castors on chairs and sofas. Alternatively ensure that office chairs and fitness appliances etc are fitted with soft, non-rubber casters. Avoid exposure to direct sunlight for prolonged periods of time and during peak sunlight hours, use drapes or blinds to minimise direct sunlight. Clean your floor regularly. Use a brush or vacuum cleaner first of all to get all the loose dirt off the floor and then use a mop to clean it. Use warm clean water and a mild, pH-neutral detergent or domestic floor cleaning emulsion. Rinse the mop regularly, mop up any residual water and then allow your floor to dry. We strongly recommend using Pure LVT Vinyl Planks cleaning products. Any other cleaning product may contain agents that damage resilient floor surfaces. Switch off or lower the underfloor heating to 15°C at least 48 hours before installation and keep it at that temperature during installation. 24 hours after installation, increase the temperature of the underfloor heating gradually by 5°C each day up to a maximum floor temperature of 27°C. Do notexceed 60W/m² with electrical underfloor heating systems .Use one of the Pure LVT aluminium threshold sectionswherever the floor butts up to a different floor covering and don't forget to allow for the expansion gap. LiViT LVT floors are carefully inspected by quality control personnel before leaving the factory. However, flooring should be carefully examined by the customer and the installer for any defects prior to installation. In the unlikely event of a defective board being found, it will be replaced free of charge. In the event that a defective board is installed whether inadvertently or deliberately, no warranty shall apply. Never use wax, polish, vinegar, abrasive cleaners or scouring agents as they may damage the finish of your floor.

Although your LiViT LVT floor is one of the easiest floors to maintain, please follow our recommendations below and that way you'll keep it looking fresh as well as protecting the factory finish. After installing your floor, give it an initial cleaning to get rid of any dirt or debris. When installing tiles, always ensure that the short end joints are staggered by a minimum of 20 cm when you start the next row. Use the leftover piece from the previous row as the first piece of the next row, provided that this piece is at least 20 cm long. To get the correct tile effect on your floor, make sure that the end joints are staggered equidistantly from the end joints in the previous row. Alternatively you can just measure the gap between the wall and the penultimate row at the middle and both ends of a board, deduct the expansion gap of at least 8mm from your measurements, and then measuring from the tongue side, mark the measurements on the decor-side of the new board. Draw a line connecting all the measurement marks, cut the board along the line you've marked and then snap in two as shown in the video above. Alterations or repairs - Alterations and unauthorised repairs to any LiViTLVT flooring will void any and all express or implied warranties including merchantability or fitness for purpose. Any authorised repairs will not extend the guarantee period.LiViT LVT should not be used in areas where drainage systems have been incorporated into the sub floor.

All flooring deliveries (boxed products and rolls of vinyl) are to roadside only - please ensure you have assistance as drivers are not insured to bring your flooring into your home. Reinstallation - In the event that we replace defective boards, we shall not be liable to provide for or incur the costs of removing or reinstalling the defective floor or resurfacing or refinishing the replaced or surrounding floor or to provide for the cost thereof unless and to the extent expressly provided in the warranty description above. No liability to replace or repair shall extend to any other materials or any other items used in the course of removal, installation or refinishing. If the floor is exposed to lots of traffic, an acrylic emulsion polish can be used to protect the floor. LiViTLVT floors have the underlay already attached to the underside of the floor and can be laid directly onto your subfloor. No other underlay should therefore be necessary.Leave Out All The Rest": Published by Universal Music - Z Songs/Chesterchaz Publishing/Big Bad Mr. Hahn Music/Nondisclosure Agreement Music/Rob Bourdon Music/Kenji Kobayashi Music/Pancakey Cakes Music (BMI)/all administered by Universal Music - Z Songs A bit of planning, a bit of care and your floor will look as though it's been laid by a professional! LiViT LVT is suitable for both residential and commercial areas such as shops, hotel rooms etc, and it's really simple to install! Wipe up any spilled liquids as soon as possible. Your floor can feel more slippery when it becomes wet. Spots, marks and spillages should be wiped up as soon as possible.