The Insights tab includes information on how much energy you’ve saved with Eco mode enabled, while also presenting a ‘Heat Report’ that details how long and to what temperature over the past day, week, and month your rooms have been heated. The TRV is liquid filled this gives a fast response to temperature and provides a greater temperature accuracy. What I always mention reviewing this item is to get any kind of accuracy with this set up (which is vital in my circumstances of course) you need one of these stats for every room, I bought the system believing the radiator valves were sufficient and only one stat was needed for “the most important/main room” my finding was despite the valves apparently being adjusted to allow for being close to the radiators when sensing the room’s temperature it just didn’t work, you got a sort of boom/bust situation. The heating would run, the area by the rad was of course much warmer than the room the valve shut the radiator believing the space was at temperature and it could be 8 degrees off..eventually the radiator would cool, the valve would realise the room was freezing..it would run the boiler/open and so on, essentially the room was never sufficiently warm. I think this is a common criticism of thermostatic valves, I’ve never bothered with them until now/my engineer doesn’t like them. Trv’s might be different in a modern/efficient house -can’t say, maybe try it out? I used my old stats display/with it disconnected as a room thermometer(it’s battery powered) to tell me what was happening in statless areas. The final component, the smart radiator thermostat, is a white plastic cylinder, which fit to the radiator once the existing valve has been unscrewed. To manually override any schedules you may have set, simply swivel the top of the radiator thermostat right to start the radiator heating, or left to stop heating. An LED on the radiator thermostat glows red temporarily when the radiator is heating, and blue if it's been turned off. Turning and holding the radiator thermostat will also reset or put it into set-up mode, depending upon how long you hold it in that position. If the valve is in the ‘Heating’ only position when the room thermostat becomes satisfied, then the valve will remain energised consuming some power and may be warm to touch. This is normal. Programmers

The information provided in this document contains general descriptions, technical characteristics and/or recommendations related to products/solutions. Typically 30M, however building construction and materials may effect this. Signal strength test should be carried out. Schneider Electric reserves the right to make changes or updates with respect to or in the content of this document or the format thereof, at any time without notice. Anyway, I got a smart central heating system right at the start of this whole energy crisis/cost of living nightmare, I can’t get a heat pump(!) likely my building is too old and energy inefficient to work with this anyway smart heating seemed like something doable/affordable The Digistat is universal because it can be used as a fully-programmable thermostat or as a simple manual thermostat. In fact it contains 4 types of functionality:What should be done when E1 appears on the screen of a room thermostat. Does the whole wireless system need replacement? Depending on the fuel type you select during installation will affect how Digistat works with your boiler/heat source - so ensure to select the correct type during installation. Digistat supports the following fuel types: To shut the valve off permanently use the plastic decorator cap that comes supplied with the valve, the valve will remain shut no matter what the temperature. The unit is simple to mount on the wall or there’s a stand, the batteries are easy to fit and it’s easy to add to the system like the other devices. If the valve is a 15, 10 or 8mm angled body then it can be fitted in either flow/return, horizontally or vertically.

From the home screen, you can also view the weather for your location and sunrise and sunset times, too. The cog icon at the top of the home screen provides access to the main Settings menu, from where you can activate smart modes such as Eco and Comfort, and set a temperature for the Away mode. The 15, 10 or 8mm angled body is bi directional as denoted by the double-headed arrow on the valve body. All other bodies are flow directional as indicated by the single headed arrow head on the valve body.We manufacture two different types of sensor kits. One is described as a remote sensor and the other as a setting kit. Drayton Wiser may be functional, but its plain all-white plastic design certainly isn’t stylish. If you prefer gadgets that make a design statement, this isn’t the smart thermostat for you. You can tap on a room and edit the schedule or access the room settings, where you can view the battery level for the thermostat, rename it and turn Open Window Detection on or off. Editing a schedule was made super-easy as a result of the ‘copy’ feature, which lets you duplicate a schedule with just one tap, rather than having to input it all for each day and on each device.