It’s very important that you don’t fill the center of your sleeve with concrete or gravel, though because this is where you will set your removable fence post when it’s in position. If you are installing your fence in a high rainfall area, you can also set this baseplate on a bed of gravel that will offer better drainage and allow water that does get into the sleeve post to drain away. If the original fence posts are painted then you will need to paint the extensions to match. You can do this before you attach them, but I think they are easier to paint after they are already attached. Make sure that you choose a day that is sunny and there is no rain in the upcoming forecast. Coat the protruding piece of dowel with glue, or pour some glue in the holes of the upper pieces, and push it onto the dowels. Tap into place with a hammer if necessary. There are several ways to remove the wood to do the lap; however, the lengths and location do play a part. A basic hand saw, hammer, and chisel, or all three have worked for centuries. Electric or battery-powered skill saws or reciprocating saws are a modern convenience that may make the task easier. I’ve seen a good hand sawer do up a set of half-laps in the same amount of time as a reciprocating saw, and with much more accuracy.

Joining 4x4s for horizontal use instead of vertical use is done in a similar way. The orientation of the cuts should maximize lateral strength while preventing the retention of penetrating moisture. The stresses applied to the skid will also affect the type and orientation of the connection. A pull force versus a downward force affects the joint differently. Post to Beam Connection Weatherables is known for creating pragmatic and minimalist sleeves for people on the go, and its line of weatherable 4x4 fencepost sleeves definitely falls in line with that reputation. The weatherable 4x4fence post sleeve is good for a lifetime warranty and it fits perfectly. Make sure this fits by entering your model number. Further, it is manufactured from premium - quality, durable pvc vinyl maintenance free.You can buy extension pieces that should fit with your original posts. Finding the right type of extender will depend on the type of fence posts in your fence. Wind loads and other lateral forces may need to be considered when orienting the direction of the lap. A connection with cuts perpendicular to the force is stronger than those parallel to the stress. When splicing four corner posts to support a roof structure, it may be recommended to alternate the orientation of the lap. To further strengthen half-lap joints use a construction grade adhesive like Liquid Nails or Loctite PL Premium. They are rated for interior-exterior use, waterproof, paintable, and even cure in sub-zero temperatures. We suggest fitting the joint together and clamping it in place, and then drilling the holes.

After fitting the pieces together, just screw them into place. 5. Place The Extender On Top Of The Post You should paint the extensions with the same steps that the original posts were painted, to ensure that they look as exact as possible. 8. Your Fence Is Ready For Panels To make a half-lap joint, measure to find the centerline of the two pieces and mark both sides at the end and near where the cut will end to form the seat. Measure from the end and mark the desired length of the cut and mark it on both sides and pieces. While the depth is always half, the length of the cut will depend on use and compliance with local building codes. If your original fence posts are concrete, you will need to use that the screws specifically made for concrete that I mentioned before. You’ll also need a carbide-tipped drill bit to be able to drill holes into the concrete. 7. Paint The Extenders Lengths of 3/8” to 1-1/4” dowels can be used to add lateral strength to butt joints. Carefully measure to bore and align 1 to 4 holes in the ends of each 4×4 and drill the holes between 1” and 3” deep. Cut the dowels to lengths of 2” to 6”, sand the cuts, glue, and tap into place.

Removable Fence Post Sleeves

The simplest way to create a removable fence post in areas that don’t get snow and ice in winter is to cast a sleeve into the ground and then use that sleeve to house the post when it’s in position. Two other reasons rest on transportation and availability issues. Carrying and connecting two 8-foot lengths is easier than transporting a 16-foot length, especially if traversing woodland trails. The availability of long 4x4s at many small suppliers is often limited due to low demand, making splicing a necessity. Repair

Our choice for the strongest and easiest way to join two 4×4 posts is a half-lap joint that is glued, plated, and bolted. Cutting a half lap into an existing fixed post is easier than all other cuts, except the butt joint. The two required cuts per post are simple and doable even with limited space. There are many reasons why you might want a removable fence post. Maybe you need to have a section of demountable fence. Maybe you need to use it as a bollard to keep unauthorized traffic out of an area. You might be wondering why this removable fence post design is only for areas that don’t get snow and ice.

Bolt In Place

Finding extenders for concrete posts may be a little tougher than other materials. Extenders for concrete posts will be made of metal, wood, or vinyl. They should look like these. They will be slotted on either side, so that fence panels will slide in and fit snugly.

To remove this kind of removable fence post, you would need to remove any fence that is installed on it and then use two wrenches to loosen and remove the bolt. Easy to Manufacture from Readily Available MaterialsWhen applied to posts that meet the requirements of BS8417:2012 - UC4 (Use Class 4). See guarantee for details There should be two bolt holes for each connected piece. Most Codes require 1-1/2” between the edge of the wood and bolt hole, which doesn’t leave much space to off-set fasteners on a 4×4. A slotted hole that is oval-shaped in the post and sleeve makes it easier for you to line up the holes on both sides and to get the bolt in place. As you will note from the sketch we’ve provided, our version of a sleeve has a pre-welded base plate. There are several reasons for this. The best way to join two 4x4s to extend a post is with a half-lap. The simple cuts make it ideal for a beginner or pro to make, and it’s easier to do in limited space. Adding glue, plates, and bolts increases the lateral and twist resistance to form a very strong connection.