Step 3: In case of an emergency, you want to know that this solution is going to work. Shut down your system and then try to start it using the keyboard key. It should turn on your computer just like it would if you pressed the power button. But even though using an external power button for a laptop is great, nothing quite beats simply using your regular power button to switch on your device! However, using this external power button for a laptop may be problematic. There have been several cases where systems may suddenly not recognize or support the external power button after an upgrade.

Due to this, the two ways of switching on your laptop without a power button we earlier discussed may be your only practical recourse. Under the button, you will see three to six pins, just depending on your laptop. Connect the pins with wire or use anything that doubles as a conductor. But when you get to the ACPI Managementfunction this time, look for the Wake On Lan or Power On Lan Option. In some cases, the name might be different, but you’ll be certain to recognize it once you see it. Your laptop will not have any power at this point, and any source of power will cause it to boot up. However, keep in mind that the ease with which you can perform this type of LAN configuration is largely dependent on your motherboard settings.Now that you have done all of those steps, you will have to take it a step further by configuring the network card to power up your system. To do this: You will have to reattach everything at some point, or your computer isn’t going to work. We recommend only using this method in the last ditch effort. – Fifth Method: Using the Lid Step 1: First, you want to access the BIOS setting interface. When you first start your computer, the BIOS can be accessed using a special key. That key is different for every manufacturer and sometimes even differs by product line, but most will use either F2, F10, or DEL. Before you try to turn your laptop on without a power button, you may want to understand why your power button broke in the first place. If you use the solutions below and you still can’t figure out why your power button doesn’t work, it could be a sign that things are going south for your computer. You need to remove the battery or any kind of power source from your laptop before touching anything inside it.

Following the steps and methods above, you should be able to easily turn on your computer even with a broken power button. Then, when it comes time to turn on your laptop without using a power button, it will be ready to go. – Third Method: The Safe Way As an example, laptop brands like Dell offer a simple external power button for laptops in the form of a simple switch you can connect to your device via the USB port. Again, here, you’ll be required to choose what key you want to be your new power button. However, this time, that key will be on your laptop itself. Step 2: Once you locate the settings, which will probably be under the “Advanced” tab in the BIOs, you need to look at “Power Management.” You will see an option that says, “Power On By Keyboard,” or something using similar phrasing. Make the changes and set a key for yourself, then you use it later on.Once you’ve located and accessed the motherboard, you can easily find the power switch. In most cases, it’s situated near the processor. Press it, and your laptop will power on straight away.

Disconnect the battery cable (not charging cable, consult your manual if you need help doing this) from the motherboard very carefully. This first method is going to work on all laptops, even if your power button is completely broken. Follow these steps closely to get the best results: If you have attempted all of the steps in this article and are still unable to turn on your laptop, the problem may not fall with your power button. It could be that some other components of your computer aren’t working properly and it just won’t turn on. This method uses keyboard BIOS and therefore is slightly more complicated. To set it up, follow these steps:

Note: You cannot do this method without the battery having at least some charge. If you try to do it while the laptop is charging, you run the risk of electrocution or frying your system. – Second Method: Using the Keyboard

That being said, using this method comes with its risks, as one wrong move can easily fry your laptop. Because of this, it’s best not to employ this approach at all or use it only as a last resort. Before moving forward, it bears mentioning that this solution is more viable for Windows users. Also, while this approach can get your laptop to come on, it only works if you’ve enabled the right features in advance. Restart your computer using the button. It may be a little difficult to press, but it will become easier over time. So, if you’re starting to notice signs of trouble with your laptop power button, you can be proactive and configure this feature in advance.

Buy it with

One of the lesser-known options is to use the wake-on LAN, which is an option for Windows 10 only. This is another method that needs to be enabled, kind of like the BIOS start-up. However, it usually isn’t the default option. It could be that your hardware has an issue. It is likely that the delicate wires have snapped or been melted. If that’s the case, the solution is easy. If you are worried about short-circuiting your laptop or running something in it, this is the method you want to use. It is safe and easy to do, though you will need to have a bit of technical prowess. Follow these steps: With that done, you’ll have to perform the following 7 steps to configure your network card, so it has the access needed to power on your system.