G Thread (Metric BSPP) Female to NPT Thread Male Pipe Fitting Adapter - Lead-Free (Two 3/4 inch)

Product Information

Inch BSP - Bathroom basin taps and kitchen sink taps, radiator connections, shower hoses, old outside tap outlets, toilet cistern fill / float valves.

The threads are rounded equally at crests and roots by circular arcs ending tangentially with the flanks where r ≈ 0.1373 P If the pressure is not going to exceed 16 bar we would suggest a John Guest PM010612E 6MM x 1/4″ straight threaded to tube adapter fitting. I've only noticed BSPT to NPT in hydraulic catalogs. It is used in the UK for general plumbing work, too.BSP sizes don't match up with what you measure on the scale of a ruler, which can obviously cause some confusion. For example a 1/2 inch BSP thread (see above) actually measures more like 3/4 inch with a ruler. DIN3852-E type pressure fittings include a channelled profile in the sealing face for accepting an elastomer seal. The main benefit of this connection type is it’s convenience at being integral to the process connector eliminating the need for additional components or alignment of the seal. 1/4 BSP-P female vsG1/4 internal thread There are no criteria to judge which Thread Process Connections mentioned above is better. Actually, each of them appears at a proper time with a proper reason. When it comes to choose a process connection, what really matters is the pipe fitting your pressure transducer is to be used. It is true that different country has its own standards and it is also a fact that any thread standard is available worldwide.

BSP is a technical standard called "British Standard Pipe". It covers two distinctly different threads: There are two distinct styles of seal typically used for pressure instrumentation with a BSP thread fitting. Parallel (straight) threads, British Standard Pipe Parallel thread (BSPP). These are sometimes denoted by the letter G, for example G 1/2" means a parallel 1/2 inch BSP thread.

Cons:

The most common G 1/4″ threads at WIKA are surely the G 1/4 in accordance with EN 837 or DIN 3852-E. But in addition there are many other pressure connections which are all specified as G 1/4″. For example G 1/4 Ermeto and G 1/4 DIN 3852-A, just to name two. Although, as indicated in the designation, all pressure connections have a thread with the nominal diameter G 1/4″, the types of sealing discern so greatly that in some cases a compatibility is not possible. BSPP (G) kinda-sorta fits 1/2" NPT, but eventually they'll leak. The pitch is too loose of a fit. The diameters are

But how about when the pressure gauge is already inserted into the process? Is there an easy way to tell which connector type an instrument has without removing it? Yes. Because a G connection bottoms out, no threads are visible. In an NPT connection, a few threads or exposed PTFE tape can be seen.At least 41 thread sizes have been defined, ranging from 1⁄ 16 to 18, although of these only 15 are included in ISO 7 and 24 in ISO 228. [3] [4] [5] [6] The size number was originally based on the inner diameter (measured in inches) of a steel tube for which the thread was intended, but contemporary pipes tend to use thinner walls to save material, and thus have an inner diameter larger than this nominal size. In the modern standard metric version, it is simply a size number, where listed diameter size is the major outer diameter of the external thread. For a taper thread, it is the diameter at the "gauge length" (plus/minus one thread pitch) from the small end of the thread. The taper is 1:16, meaning that for each 16 units of measurement increase in the distance from the end, the diameter increases by 1 unit of measurement. A 1/4 BSP (G1/4) thread has a 13.157mm outside diameter and a 1/2 BSP (G1/2) thread has a 20.955mm outside diameter. 0.25-18 NPT thread explanation Since the thread of a G connection will bottom out at the wrench flat, no threads are left exposed. Once the connector bottoms out to make the seal, the positioning of the instrument cannot be changed. To avoid the problem of awkward gauge positioning, use a “crush washer” and hand-tighten the connection. At the resistance point, approximately 1½ turns are left before the crush washer flattens out. This leeway allows the user to fine-tune the pressure gauge’s final position with a wrench**. If the position of the instrument is not critical, a flat washer can be used instead. Eyeballing the Difference Between NPT and G Connections I have a pressure sensor for use on air with a G1/4 female process connection and would like to convert it so it can accept 6mm OD tubing. Would you have some kind of adapter that could do this? The sealing technique for both types is fundamentally different, NPT relies on the gradual compression of the flanks of the internal and external thread to directly form a seal on the thread, whereas a G1/4 provides the mechanism for compressing a seal typically between two flat surfaces at one end of the male thread. Adapt G1/4 (1/4BSP) female to accept 6mm OD tubing

BSP Male DIN16288 and G1/4 Male EN837 are a couple of examples of how this style of connection is described. Prefixing with G, is equivalent to adding BSP after the pipe size, although BSPP is more strictly correct to define the parallel version. The adapter has a built-in O ring seal which acts the same as bonded or dowty seal for sealing the 1/4 BSP (G1/4) thread end. In the USA, NPT (National Pipe Tapered) is the most popular process connection, especially in businesses of oil and petroleum. Compared with BSP, NPT is easier to cut and user-friendly, and is considered a booster to American Industrial Revolution. Being a kind of screw thread system, NPT is tapered thread with the pressure tight seal being made on the thread itself. The most common sizes are 1/4, or 1/2 inch NPT. 1/2"NPT MALE Where can we source a pressure DP transmitter flanged with a flush diaphragm for liquid level measurement with an output over 0-200 inH2O? The threaded part(s) of plumbing fittings are usually made to a British Standard Pipe Thread size (BSP).

Order Approval

DIN3852-A is used with a bonded seal (also known as a Dowty seal) which is a steel washer that has an elastomer ring bonded to the inside diameter of the washer. Some pressure connections also include a tapered shank which assists in the correct alignment of the bonded seal. If there is no tapering it is advisable to use self-centering bonded seals to avoid a poor alignment of the seal which may compromise pressure tightness. International Standards Organization Specification 228/1, straight threads, reference specification: BSPP, DIN 259, JIS B0202. The standard ISO 228 - Pipe threads where pressure-tight joints are not made on the threads consists of the following parts: external) & 3B (internal): for applications where closeness of fit and/or accuracy of thread elements are important.