High pressure hand pumps (HP pumps). These pumps are designed for the small, hard racebike tires. They generate high pressure and apply the correct amount of pressure to your tires easily. (ideal for race- and road bikes). Pumping at altitude is a problem, because air is thinner the higher you go. This starts becoming noticeable above 4,000 feet, and past 8,000 feet it's very noticeable. You also have problems shooting spring-piston guns at altitude for the same reason.

The ABS Flex Hose is equipped with the ABS system, which causes you to bleed the hose before disconnecting it.High Performance: Our stirrup pump include precision pressure gauges used to monitor the pressure level, the maximum pressure can reach 4500psi, the air hole and the air pipe are tightly integrated to ensure smooth inflation Material: The high pressure hand pump is made of high-grade stainless steel, which is safer than other materials. The 3-stage air gun pump with an ergonomic handle is more labor-saving than other pumps. What you will get: 1 x Assembling the Pump Main Unit, 1 x Handle, 1 x Foot Pedal, 1 x Hex Wrench, 4 x Mounting Screw, 1 x Pressure Relief Valve Screw, 1 x Small Rubber Ball, 1 x Spring, 5 xRubber Seal, 1 xThree-Stage Piston Ring, 1x Test Plug, 1 xTire Inflation Conversion Head, 1 x Manual The only real maintenance you can do for the pump is to bleed it correctly. As long as you bleed from the pump's base and not from a refill device, the pump will take care of itself. You can also periodically lubricate the O-rings of your refill devices, but remember that grease attracts and holds dirt, so they must be protected if they are greased. Some PCP airguns use a fill probe to connect the pump to the gun. The Umarex AirSaber and the new Umarex Origin are examples. These typically have two O rings around the probe.

The HTP1 hand pump provides pressures of up to 700 bar using hydraulic pressure. The reservoir has a 100ccm capacity and will accept Hydraulic oil or distilled water as a pressure medium. The fine adjustment valve (which is integrated in the pump) allow for precise adjustments for more accurate pressures. This unit is supplied with accessories (Hose, adaptor, etc) in a stable carrying case. We have a team of expert technicians and a complete repair shop that are able to service a large variety of brands/models of airguns. It can be disheartening to see the needle on an air gauge rise and then fall. It may even take several strokes to raise the needle by a mere 100 PSI… High-Quality Material]High-grade stainless steel pump body does not heat up with constant use. Which is safer than other materials; all spare parts use advanced CNC technology. Made of high-grade 304 stainless steel with a tungsten coating finish that prevents rust and ensures fadeless performance.The larger the reservoir, the more pump strokes it takes for the needle to rise and remain there. A larger reservoir (like a 24 cubic inch vs a 14 cu in cylinder), delivers more shots per fill. It may take more pumps to fill it to capacity, but it evens out on the shooting end. If you live in a state or city where air guns are treated as firearms you may be able to take advantage of our FFL special program.

Ten-meter target airguns have removable reservoirs that attach to a pump like this. They come with a DIN adapter and require a pump with a DIN hole in its base.DO NOT attempt to disassemble the hand pump! There are more than 20 different O-rings inside and most are lubricated with a special grease that's not easily available. Disassembly of the hand pump almost always results in damage that cannot be repaired. Do not remove any lubricant from the pump shaft. This lubricant is dark and will stain clothing, but it is not moly grease as many people have supposed. If you remove it, your pump will soon fail. A good rule of thumb is to pause one full second at the top and bottom of each stroke. Three-stage air gun hand pumps work during both the up and downstroke. You will feel the most resistance on the downstroke but don’t discount the upstroke. A scuba tank can take care of business very well, and a carbon fiber tank can do even better, but there will always come a day when you're down to 2,200 psi and the dive shop is closed. The hand pump never runs out of air. As long as you are breathing, your pump has what it needs to fill your airgun. Every brand of airgun uses a different type and size of fill adapter. This is where a good dealer like Pyramyd Air is a great help to you, because they know what kind of adapters their guns require and they can make sure you get what you need. Other airgun dealers may not know or care about this issue and leave it to the customer to resolve. This is one of the biggest problems PCP guns have, so be sure you always get the dealer's guarantee that you are buying everything you need to fill your gun. If you buy from Pyramyd Air, you are assured of it.

Many experienced airgunners agree that Hill pumps are the most durable and consistent hand pumps on the market. They're easy to use and maintain, and they're very reliable.

Hand Pumps for Pressure Generation

It's important to know that due to state and local laws, there are certain restrictions for various products.