RK808-D PMIC, cooperated with independent DC/DC, enabling DVFS, software power-down, RTC wake-up, system sleep mode Disadvantage of a regular desktop is power usage... Should you decide to use a PC there are a couple requirements. The front side of the devices comes with two USB 3.0 ports, a MicroSD card slot, and what looks like a standard thread to mount cameras…

Hook up WAN to your modem. Hook up LAN to either your switch which connects to a computer or hook up LAN directly to your computer. Power Input: 5V/3A, via USB Type-C(USB PD Specification is not supported) or Pin1&Pin2 of the 2x5-pin headerif you want some acutal logging btw. make /etc/hotplug.d/ntp/20-ntpd-logger and put the following in it. Improved stability on first boot (previous version, bpfilter error occurred in some cases on first boot) wondering why they can't get a goodput of more than a certain very small amount on a Fast Ethernet connection*.

Available, device name is /dev/ttyS4 (note: this is only applicable for ROM released after 20180618) Step 3: The Performance Tweaks. Putting affinities on Faster A72 Cores. Queues to spread evenly on slower A53 Cores.I'd prefer it as a separate script you could add in that you copy over as it is a change from the default settings that are provided. That way we know out of the box to expect "x" setting and we can edit/change for our settings. Would you copy yours to the wiki? It was one of the reasons i put wallmarts post into the wiki for others to tinker with. Also in the linked example, I notice I have the vlans (1, 10, 20, 30 for lan, IOT1, IOT2 and GST) only set up as coming in on port 1 of the dumb AP for wireless availability. For using the dumb AP as a switch and AP with the NanoPi, you'll want to list out the rest of your physical ports. For example, you might change this: config switch_vlan Setting up a single board computer (SBC) or even a computer, for both regular or server use, takes time and skill. DietPi provides an easy way to install and run favourite software you choose. Note: The contents of this section are based on firmware released after 2021/08/31, kernel version kernel 5.10.xyz） This method firstly boots a mini Linux from a TF card and then automatically runs an EFlasher utility to install the OS to eMMC.

If ifconfig -a sees wlan0, but the hotspot is not working properly, try changing the channel and country code, an inappropriate country code can also cause the WiFi to not work. GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] } Eject the TF card, insert the TF card to NanoPi-R4SE, power it on it will automatically install your firmware. You can watch the installation progress by observing the LEDs’ status.Note that if you are burning the FriendlyElec firmware, you need to use an image file with the "-sd-" file name, similar to the one below:

Well, that is a valid choice, but whenever your link gets saturated, be it transiently only or continuously, the default FIFO with too deep buffers is going to introduce additional variable latency to your flows. If you can either guarantee that you will never fully saturate your link or that you never use latency-sensible flows (like even interactive web-browsing to some degree) then it is a no brainer to not waste CPU cycles on traffic shaping. If you are not 100% sure traffic shaping might be worth trying out. wget https: //raw.githubusercontent.com /friendlyarm /sd-fuse_rk3399 /kernel- 6.1.y /prebuilt /boot /logo.bmpBy doing this way using this file, the change is permanently and you dont need to dedicate anything else just to make it like that, like a script that executes at boot or using rc.local and etc.