I did not got an answer for wich Tamiya polish I should use. I saw that they sell three different kinds and I think that it is for the shelf queens. Is it possible to use just one for an ok result? In this Sunward Hobbies Tutorial, you’ll be seeing how polishing your model with Tamiya Polishing Compound can make a huge difference. Also, I’ll throw in some items which will make your life easier, give an even better finish and possibly save you some money. It took only a few drops and two applications to get the result you see in this shot. Very simply, you rub it on, wait a few minutes for it to dry, gently polish then rinse and repeat. The results are stunning. Super Mirror Finish with Silver Cloth Besides

I also tried it on some spoons with the LP paint on tonight, not clear coated and I couldn’t replicate the problem with the Alclad so the Tamiya TS spray is more robust than the Alclad clear! Still I couldn’t get a noticeably different finish between polished and non polished after 3x fine and 1x finish The final Tamiya application was with their Finishing compound. Here I did 2 or 3 applications to get a mirror finish. If you look closely, you see the reflection of my glasses and finger at the bottom of the polished part. It’s quite remarkable the look you achieve with not much effort. The great thing about Tamiya’s Finishing Compound is that it can be used for any general polishing, such as removing fingerprints or getting rid of water marks around decals. Fine Compound with Applicator and Silver Labeled Tube my objective is to get a nice glossy shine on my car body like I’ve seen people get on YouTube by using it. They tend to sand the body first with 6000/8000 grit sand paper For the course compound I went against the scratch grain to cut down the hills. It took less than 5 minutes of this motion to see a difference then I swirled for another few minutes. The course compound usually has had enough when it begins to cake, as in the picture. Don’t fret, we’ll look after that in a jiffy.) Dried Compound on Part with Applicator Clear coating gives a much better surface to polish your model and you don’t have to worry so much about digging into the color paint layers. It also will fill in those micro scratches and level out super smooth. There are many clear coat products which Sunward Hobbies offer, in this case it’s Tamiya X-22 Clear, again reduced 50/50 with Mr. Leveling Thinner 400. Mirror Finish on Part in Blue GloveI'm afraid 2000 will clog up right away. (Also, it would take forever.) I would try #800 or so and see how it goes. It depends on how much paint needs to be removed. You can start with 800, but I have a feeling that's too fine. There is no set rule, so you would have to judge as you sand. Coarse grit (like 600) will get things done faster, but you don't want to leave deep scratches. So starting with finer grit than you think you'd need is a better idea. If it takes long, you can go slightly rougher to do the majority of the sanding done. Just as in the automotive industry the key to a good finish is in the preparation. A shiny surface will show many flaws, thus to begin I’m going to make certain that the surface of my plastic is as even and smooth as possible. In this example I’m using the bonnet of my Tamiya Lotus Super 7. For demonstration I’m hoping for flaws to show you. Now these spots can be sanded smooth again. I’m going to reduce my second primer with Mr. Leveling Thinner 400 because it self levels. Here’s a tip, find a cover for your part to prevent unwanted dust or lint from gathering on it. Mr Leveling Thinner 400 with Flawed Part Getting a mirror finish takes a bit of effort, yet when you see the results I’ve shown it’s more than worth the minimal amount of elbow grease. Talk about gratification. At this point you can choose to reapply the course compound or move on. It depends on your theme and desired look. Make certain, though, you wash your applicator in the warm water. Takes but a few seconds and ensures what is put on it next is not contaminated by the previous job. Rinsed Off Part with Course Compound Behind

This article will focus on Tamiya Polishing Compounds and how we get to that point, so let’s grab a bunch of items from the store and have some fun. Many Items Gathered Together as I say I was only using the chrome and aqua clear as a test as I had it ready sitting there cured. I’ve painted another 2 test pieces with my main subjects colours. Tamiya TS spray then 3 coats of Tamiya LP gloss clear. I will give it 3/4 days and then try the compounds on those. Then go finer, like 1000. Usually 1000 is enough for my bashers. But if you want more, you can use 1200 or 1400. I don't think going beyond 2000 is meaningful. As the paint solidifies, the paint surface is what makes it smooth. Even if you make it as sooth as the reflective surface of Hubble telescope, it won't matter. The reason why I still do 1200 or 1400 sometimes is to make sure that 1000 grit did not miss 800 scuffs. So 1200 or 1400 is like a quality control for me. 2000 would be extra nice. Now let’s have a look at the part after drying for 48 hours. It’s vital to let your painted parts cure for no less than 2 days, yet I’d strongly recommend a week or two even. You can see the glossy shine is gone and many micro scratches came through. There are 3 coats of paint on this bonnet so you have a choice. You can polish now, and hope to reach the level of the valleys, or you can clear coat. Please consider clear coating, it’s far less messy, hence why I did. Near Mirror Finish of Part Resting on Blue Glove Sorry about the slightly out of focus shot, but you see the marks have been erased and another coat of primer added. I bought a can of Tamiya TS-9 British Green for the model and because dark colors show flaws. TS-9 with a Clean Primed PartNow we’ll apply Tamiya Polishing Compound “Fine”. With this product using a swirling motion is all that’s needed. Spend a few more minutes here to make sure you’ve got any micro scratches left behind from the previous “cut”. Again, it takes very little compound to do an area. Fine Compound with Part and Blue Labeled Tube I should have asked OP how bad was his "Orange Peel of Doom." Old people tend to make assumptions, and I thought of my own novice mistake from 20 years ago. It has the classic orange peel. (Scout's honor! I'm not this bad anymore, I hope... but everybody starts as a noob.) The left side was corrected with a rotary tool and jeweler’s rouge. The right side is Mr. Hobby Polymer Finish and the “clear” winner! You can easily see my fingers and the reflection from the camera lens while the left side is far more distorted. I highly recommend this product and can’t wait to use it again. Polished Part with Keyboard Behind