Our special polypropylene mix has been specifically blended for super high impact resistance and cold weather performance: COMPATIBILITY WHEELS: 26” 27.5” 29” TYRES: up to a 3” tyre BRAKE / OFFSET: MINIMUM 44mm HUB: STD & BOOST FORKS:

Our widely acclaimed Seal Shield has made it to the PROGUARD as a means of offering greater protection for your seals from high velocity mud and spray, the Seal Shield section also provides additional strength and rigidity to the rear reducing flex MAX PROTECTION VERSION Important - The snap-off hole will break off fast so ensure thre is nothing underneath the guard that the screw driver can hit, failure to do so may lead to damage or harm Standard: 503mm long - 130g (without bolts) COMPATIBILITY WHEELS: 26” 27.5” 29” TYRES: up to a 3” tyre OFFSET: MINIMUM FORK OFFSET 44mm HUB: STD & BOOST FORKS: The ProGuard range of mudguards have a matte textured finish with gloss highlights on the logos and centre strip. The underside features a smooth lightly polished finish for better mud flow.Then feed cable ties through teh sames holes from the rear to the front (you must use min 5 cable ties to ensure the guard is secure) RapidRacerProducts Ltd, Parkfields Business Centre, Park Street, Stafford, ST17 4AL, United Kingdom

Chain reaction Cycles and CRC are trading names of Wiggle Ltd (In Administration) registered in the United Kingdom at 1000 Lakeside, Suite 310, Third Floor N E Wing, Portsmouth, Hampshire, PO6 3EN, From time to time carriers may deliver earlier or later, or on non working days however this is cannot be guaranteed nor should it be expected.The best mountain bike mudguard currently available on the market is the RRP ProGuard Max Protection Mbr Magazine (Feb 2020) Finally tighten the bolts to the torque settings below: TORQUE SETTINGS: FOX, MARZOCCH & OHLINS = 1nm | SR SUNTOUR = 2nm GT85/WD40/Solvents - Only rub these on the surface if you want to remove the gloss and display a matte finish to match your bike. The ProGuard BOLT ON will fit most fork models listed below if they have the *THREADED HOLES at the rear of the fork brace (DISK BRAKE ONLY): WHEELS: 26” 27.5” 29” TYRES: up to a 3” tyre BRAKE / OFFSET: MINIMUM 44mm HUB: STD & BOOST FORKS:

The ProGuard - BOLT ON is our direct mount front mountainbike mudguard designed for big spray and mud protection (DISC BRAKE ONLY) Forks: This direct mount mudguard is designed for the forks listed below ONLY IF THEY HAVE Threaded holes in the rear of the fork brace Fits Fox 32, 34, 36, 38, *40 (2021) 49 Use the Allen key provided to screw the bolts in EVENLY a bit each side, go gentle to start off to ensure you DON'T CROSS THREAD THEM, stop once it's pulled together so you can still move itFinance is subject to application, financial circumstances and borrowing history. Performance Cycling Limited FRN: 720557 trading as Tredz are authorised and regulated by the Financial Conduct Authority. We are a credit broker not a lender – credit is subject to status and affordability and is provided by Mitsubishi HC Capital UK PLC. Terms & Conditions Apply. long 24g (without cable ties) MAIN DISTRIBUTORS UK EXTRA UK FRANCE TRIBE SPORT GROUP NORWAY DELER AS REST OF EU NOW COMPANY USA AND CANADA RECIPROCATORS As for the fender itself, they're the cat's ass. I've had mine for over a year now, and have used it everywhere from WBP (Older Boxxer) to general aggressive trail riding (DVO Diamond), to faffing around on my hard tail ('14 Fox 34). It's sooooo nice to not worry about crap in your eyes or continuously cleaning your goggles. I got caught in a proper North Van squall yesterday, just as I began my ride up No Quarter on Fromme. Didn't even care, and not a drop of spray or particle of grit in my eyes for the entire ride.

We offer the longer MAX PROTECTION version to be the best protection in the world, this version is 68mm longer at the rear. No other mudguard offers more protection MATERIAL Important - If you have a brace between the seatstays - you must attach at least one cable tie to it if you don't have a brace between the seatstays - you must use 3 cable ties on each arm You can also change the height of the mudguard by 6mm through the slots for more clearance. NOTE: Highest position offers the most stability with the best mud clearanceAs a result of achieving the above properties it means that the surface layer is soft and will scratch easily, you must also be careful about putting any chemicals onto the surface as it may tarnish the finish. That said we have tested and can recommend the following chemicals to use: This mudguard design is perfectly suited for the rigours of modern mountain biking. It ensures superb all-weather protection for anything from Enduro and Downhill racing, to weekend Trail sessions with friends. And, since it’s made from RapidRacerProducts’s unique polypropylene, it gives a superbly flexible and ultra-durable performance at a low weight. INSPECT BEFORE YOU RIDE: DO NOT USE IF DAMAGED IN ANY WAY AS CONTINUED USE MAY LEAD TO FAILURE OR INJURY If you find an item at a lower price with another commercial internet retailer, you will receive it from us at the same price, provided the conditions listed in the link are met. The ProGuard range of mudguards have a soft high gloss finish which is a characteristic of our highly polished mold and our special polypropylene mix, this unique mix has been specifically blended for: