Cooler Master TD500 Mesh, Mid-Tower

Product Information

One other thing worth mentioning is the RGB control button. Unlike most case RGB hubs that switch between a manual button and motherboard RGB control by holding in the RGB/Reset button for a few seconds, the Cooler Master RGB hub doesn’t have this capability. If you want to control RGB lighting with the switch you must not connect the motherboard header cable from the hub to the motherboard.

TD500 Mesh V2 is equipped with a Polygonal FineMesh front panel with a 3D effect contour design which is capable of providing high airflow and dust filtration, so there’s no need for an additional dust filter up front. To look at the TD500 Mesh V2 you could easily mistake it for the original. In terms of the visuals not much has changed at all. It still has the Polygonal FineMesh front panel design, it comes with three CF120 ARGB fans pre-installed up front and features the Crystalline tempered glass side panel like the original. But there have been some subtle changes, the case is a little taller, the top panel is now removable, there's a cover for the PSU shroud window and USB type-C has been added to the front I/O panel. Installing a system into the Cooler Master MasterBox TD500 V2 is a simple and pleasing process. Cooler Master has everything laid out in the correct positions, everything is where you would expect it to be. Alignment of PCIe slot cutouts, motherboard standoffs and fan screw holes etc are all good, nothing was difficult to install due to alignment issues, which can be a problem on some cheap chassis. Removing the front panel had little effect on CPU and GPU temperature, but as we often see, removing the side panel offered a slight improvement in both CPU and GPU temperature. Adding a rear fan had no positive effect on thermal performance. So in its default configuration, the case flows air well and is able to keep high-end components cool.Radiator support at the top of the case is better, with 120mm and 140mm mounts extending the whole length of the case. Clearance from the top edge of the motherboard to the top of the case is just 3cm, but the radiator/fan mounts are offset a bit towards the side of the case away from the motherboard. The distance from the motherboard tray to the 140mm mounting location is approximately 4cm, and that makes the distance to the 120mm mounting location approximately 6cm. During our thermal performance tests the case held up well, keeping the high-end CPU and GPU nice and cool even under the extreme load that we put the system under. Yes, that is down to the excellent EK-Nucleus AIO CPU cooler in part but a good cooler needs a good airflow-optimised chassis to operate to its full potential. The Cooler Master Polygonal front mesh seems to allow ample cool air into the system.

The narrow case design also means that users could run into space issues with some new Nvidia RTX 40 series cards. There is only 175mm space between the motherboard standoffs and the TG side panel. Our test system card measures 140mm wide, when installed and connected to PCIE cables there isn’t much gap to the side panel. A wider RTX 40 card using a 12VHPWR adaptor cable could be pushing the case limits and the cable could be trapped against the side panel. As well as three ARGB fans, Cooler Master includes an ARGB/Fan hub with the TD500 Mesh V2. The hub supports up to 4 fan header connections and 5 3 pin 5v ARGB connections with the front panel reset switch re-purposed to become an RGB control button. The hub also supports motherboard RGB control. Cable management space is tight behind the motherboard tray. Cooler Master lists clearance as 1.9mm, but that’s the maximum depth, and in some locations clearance shrinks towards 1.5mm. The tie points next to the cable cutouts and the space under the PSU shroud make management possible, but the small amount of clearance combined with the already difficult-to-wrangle steel side panel aren’t fun to deal with.MCB-D500D-KGNN-S01 (Mesh w/ Hub), MCB-D500D-KGNN-S00 (Mesh w/o controller), MCB-D500D-WGNN-S01 (Mesh White w/ Hub), MCB-D500D-WGNN-S00 (Mesh White w/o controller) Mini ITX, Micro ATX, ATX, SSI CEB, E-ATX*, (*support for up to 12" x 10.7", will limit cable management features) As usual with case noise testing, removing the side panel lowers noise since the fan RPM is reduced due to the cooler temperature of the components. With the case in its default configuration noise output was measured at 51dBA which could become a little distracting for some users. Manually tuning the fan curve may be required to keep noise output more comfortable. Closing Thoughts

Dimensions (L x W x H): 499 x 210 x 500mm (incl. Protrusions), 430 x 210 x 477mm (excl. Protrusions) Prior to load testing, we collect idle temperature results for ten minutes to determine the unloaded cooling performance of a case's fans and air channels. Thermal benchmarking is conducted for 1400 seconds (23 minutes), a period we've determined sufficient for achieving equilibrium. The over-time data is aggregated and will occasionally be compiled into charts, if interesting or relevant. The equilibrium performance is averaged to create the below charts. The listed specs for drive mounting are somewhat misleading. For 2.5” drives, Cooler Master has included a set of rubber stoppers and metal posts that allow drives to be pressed into place without being screwed down. We’ve seen this system in past cases, and we like it. The misleading part is that the spec sheet implies that there are only two 2.5” mounting locations outside of the HDD cage, but what it actually means is that there are only two sets of stoppers and posts. There are four mounting locations, two on top of the shroud and two behind the motherboard tray. GN Case Testing Bench Firestrike is next, our gaming stand-in. The TD500 Mesh isn’t at the absolute top of the chart here, but it’s pretty close. 49C dT ties it with the P400A Mesh and gets it pretty close to the O11 XL again, although the larger temperature range reveals the SL600M’s advantage with an average of 46C dT. The 500DX averaged 53C dT in this test, giving the TD500 Mesh a slightly larger advantage than it had in the torture results. Standardized FansA full-cover power supply shroud with a front cut-out for long radiator installation and a PSU window with a removable cover allows the user to choose whether to show or keep the power supply hidden. KitGuru says: A few minor changes to the chassis have certainly improved things compared to the original. However, it is still a fairly narrow ATX case which may compromise some builds. Will any of you guys be buying one? Radiator Support: Top120mm/140mm/240mm/280mm/360mm, Front 120mm/140mm/240mm/280mm/360mm, Rear 120mm Mini ITX, Micro ATX, ATX, SSI CEB, E-ATX*, (*up to 12" x 10.7" motherboards, may impact cable management feature) Added support for USB Type C front connection with a USB 3.2 Gen 2 Type C port alongside two USB 3.0 Type-A ports now on the front panel. The original TD500 Mesh had only USB Type-A front panel ports.