USW-Flex — When using PoE passthrough ( Note: this was upgraded to 802.3at PoE+ in a firmware update) When the reboot is completed the led will turn pale blue. You can now adopt the switch in the controller Have a small touchscreen on the left side of the device, like the UDM-Pro. This screen shows stats and info about the device, and the network it is on. They also integrate with the UniFi AR feature, which lets you use a phone to virtually see what is connected to each port. Most UniFi switches operate at layer 2, meaning they can handle VLANs but cannot act as a router. The 2nd generation pro and enterprise UniFi switches have some layer 3 features such as static inter-VLAN routing and DHCP, but they require a separate router or firewall for everything else. UniFi L3 switches can’t compete with a true enterprise product from a vendor like Cisco or Juniper. UniFi switches are a fraction of the price and don’t require licensing, so they compete in different markets. As with all network design and purchasing decisions, what matters most is your budget and your use case. EdgeSwitches have an optional web interface overlay called UISP, which is similar to the UniFi controller. UISP is limited when it comes to EdgeSwitch configuration, and it doesn’t have every option that the device’s individual web GUI or CLI has. Think of UISP as an easy way to monitor all of your AirMAX, LTU and EdgeMAX devices, rather than a single interface for configuring everything like the UniFi controller.

To cache the firmware in your controller you open your controller and go to the settings (lower left gear icon). Search for Firmware and select Device Firmware Cache (or select Updates > Firmware in the settings menu) Passive 24V and 48V PoE — Ubiquiti’s standard, mostly used on EdgeMAX, AirMAX, and older UniFi devices We use the Ubiquiti equipment at work (mainly the access points) and have been very impressed with how they are built and their reliability. We have a couple hundred access points in service now for three years, only one died and was replaced under warranty.

Ubiquiti US-16-150W 16 Port Gigabit Switch

EdgeSwitches are more flexible and capable, and are a better fit for network operators, WISPs, managed service providers, and other more advanced networks. If you need features like link aggregation, TACACS+, RADIUS, 802.1X, MAC filtering, ACLs, or static routing, you’re better off with an EdgeSwitch than a UniFi switch. UniFi switches support many of these features, but are often less configurable, poorly documented, and less reliable. Wait for the device to fully boot, the led will turn dark blue (or stay white if it wasn’t adopted before, approximately 5 minutes max) EdgeMAX products are managed with a per-device web interface, or via SSH. These web interfaces are not as polished or pretty as UniFi, but they expose more advanced features than UniFi does. EdgeSwitches also have the full EdgeOS CLI for configuration. If you’re familiar with JunOS or IOS, you’ll be able to figure out your way around. See Ubiquiti’s CLI Command Reference user guide for more details. Also worth noting — if serial console out-of-band management port is something you need, the first generation switches have it, and the second generation models do not. XG UniFi Switches PoE+ devices like the U6-Pro will usually operate with 802.3af input, but they will be unreliable. It’s never a good idea to push past your budget, feed a PoE+ or PoE++ device with a lower tier of PoE, or supply the wrong voltage. Always follow the recommended input power, and never provide less the required power or a different voltage.

Basic layer 3 features like static routing (supported as of firmware version 4.3.13.11253) and inter-VLAN routing.

Standard warranty: 1-year

If you want 10 Gbps ports for clients, or need a distribution switch to aggregate other switches, the XG series has a few options. Some are in the 1st generation, some are in the 2nd: If you are planning on using PoE passthrough on switches like the USW-Flex, or access points like the In-Wall-HD, you should supply them with the higher-wattage PoE+ or PoE++. Devices with PoE passthrough will usually function when fed with standard 15W PoE, but will not reliably power downstream devices unless they receive their maximum rated power input. For example, the USW-Flex can provide 8W with PoE in, 20W with PoE+ in, and 46W with PoE++ in. Its enterprise level equipment, so you pay a little more than consumer, but it is in reach of a homeowners budget. I highly recommend it. Read full review I have both connected to the could so now I can configure/adjust my network from anywhere and view live video as well. It’s also worth pointing out that PoE devices don’t always consume their maximum rated power draw. The spec sheet will specify the maximum amount the device can use, but during normal operation they won’t use that much. For example, the U6-Pro requires 802.at PoE+ or 48V passive, and maxes out at 13W. During normal use it usually consumes around 5 to 7 watts of power.

The main point I’m trying to make here is that if you expect a UniFi switch to be your only layer 3 device, you’re going to be disappointed. Adding layer 3 at the switch level usually doesn’t make sense in small to medium sized networks, and I wouldn’t recommend relying on UniFi layer 3 switches in general. If you’re working on a large multi-building network with high requirements, UniFi may not be the best fit. I’ll cover this in more detail if I ever get around to finishing my USW-Enterprise-8-PoE review. I mounted it, plugged it in to power and the other switch I had. By the time I got upstairs, the controller already found the new switch. This Ubiquiti US-16-150W UniFi switch offers sixteen (16) PoE Gigabit Ethernet ports of auto-sensing IEEE 802.3af/at or configurable 24V passive PoE to simplify your infrastructure. By default, the Ubiquiti US-16-150W UniFi switch automatically detects 802.3af/at devices so they automatically receive PoE. For 24V passive PoE devices, manually enable 24V passive PoE using the UniFi Controller software. Fiber Connectivity Deciding between UniFi, EdgeMAX, UISP, or some other brand depends on your needs. The right solution varies with what kind of network you are trying to build, and what features you need to accomplish that. If you are comfortable with command line configuration and have complex needs, another vendor is probably a better option. This guide focuses on UniFi switches, but it’s worth noting some EdgeSwitch models are the same hardware as the first generation UniFi switches, with an EdgeOS CLI and UISP instead of the UniFi controller. The newer UISP switches are not as mature, but are worth considering if you want your switch to tie into the UISP NMS and UCRM software.I’ll use the PoE, PoE+, PoE++ names as shorthand. It is important to consider the type of PoE you need for your devices, and to make sure that you have enough PoE budget on your switch to power all your devices. Otherwise, you will need to rely on separate power injectors. PoE Passthrough The USW-Flex-XG is a 2nd gen model, with one 1 Gbps and four 1/2.5/5/10 Gbps RJ45 Ethernet ports. No PoE. One limitation of the regular second generation switches is their limited PoE budget. PoE budget refers to the total amount of power available for all PoE devices. Since the non-pro 2nd generation models are fanless, they also have smaller power supplies, and a smaller PoE budget.

Do not have a serial console port. All management has to be done over Ethernet in-band. (EdgeSwitches still have console ports!) Putting the L2/L3 differences aside, the 2nd generation pro models also have some other advantages over the non-pro UniFi switches. 2nd Gen Pro models add A common complaint with the first generation models are their loud fans. It is possible to replace them with quieter Noctua fans, or you can throw it in a network closet and forget about it. If you just need basic L2 switching and PoE, the first generation models are still worth considering, especially if budget and availability are more important than future software support.

If you keep having problems with the installation of the firmware you can also try to install it your self directly on the device. To do this we are going to access the device using SSH. Higher PoE budgets. The 2nd generation non-pro models are fanless and have very limited PoE budgets The US-XG-6-PoE has four 1/2.5/5/10 Gbps RJ45 Ethernet ports with PoE++. It also has two 10 Gbps SFP+ interfaces. I have been working a lot with Unifi devices and sometimes you just got one of those devices that just won’t adopt. You may get an error that a firmware update is required or you can’t simply find the device in the controller.