Joined in 2023 
82 
63 About this deal
The D1 Pro is equipped with a transparent safety shield over the laser module, however there is a slight gap between the shield and the material. Because of this gap, you must always wear safety glasses that protect you from the 455 nm (blue) wavelength light. A pair is provided with the machine. After looking at the insulated cup, I'm doubtful this would fit my needs for precision-cutting small batches of sheet aluminum. I recommend an enclosure with any laser product, I bought the xTool one, but that's another review. Fit the four side plates together. Align the power switch, power port, and USB port with the openings on the right plate. If you can't put the shaft through the timing belt, the possible cause is that the timing belt is set too tight. You can adjust its tension by turning the screw.
This software is easy to operate and everything a beginner needs. It’s also tuned to work specifically for your laser – you must link the laser to the software – and has many helpful presets for materials sold by xTool. You can draw shapes, vector lines and add text with XCS. Best of all, the software understands JPGs so you can import photos and clipart without trouble. Insert the connectors into the port on the main control board and the one on the motor, respectively.When you hit the Framing button it will instruct you to push the button on top of your xTool D1 Pro. Then the framing operation will begin. You can do this as many times as you need to. Since the laser is literally burning material, never allow it to operate unattended and have a fire extinguisher handy just in case. After adjusting the position of the rear plate, you can still use the focal length setting bar to set the position of the laser module. The air assist blows cool air onto your work surface, which prevents charring while also keeping the smoke from gunking up the laser lens. The results are cleaner cuts, less charred looking engraving and a safer experience. The air pump and tubing are much like those seen on a fish tank or airbrush, and just as noisy.
Ex. some 'wood' may be more thermally-conductive or moisture-laden than others samples of the same species. The D1 Pro is also compatible with LightBurn, a premium laser program, for advanced users. Engraving / Cutting with the xTool D1 Pro Insert the connectors of the laser module, motor, and limit switch connection cables into the ports on the main control board, respectively.Now we’ll Frame our letter T and that will send the laser head to where the T is located in the workspace. Right at this moment we don’t care where that location is. We just want to test our machine. Rotary Engraving Available w/ Starter and Standard Bundle MORE MATERIALS, MORE CREATIONS Produce a variety of projects out of a variety of materials thanks to the xTool D1 Pro's compatibility with engraving and cutting a wide catalog of materials. When the light shield is dirty or laser beams can't cut a material, you need to clean the laser module. The air assist and honeycomb bed are *ESSENTIAL* for most jobs, especially when it comes to cutting. If you want a professional finish without the charred look, you need to be running an air assist module and the honeycomb base, there is are little to no projects that work better without them.
Try to set the timing belts on the right and left plates to the same tension, so that xTool D1 Pro can cut and engrave materials properly. The optional enclosure is well worth the extra cost, as it completely seals the laser from view. It also helps control smoke emitted from the materials that you’re burning. A small fan is included to help pull the air through a hose, which you can then hook up to a vent or other purification system. Put the shaft through the coupling, and then put it through the timing belt and insert it into the idler pulley. The screw is used to set the tension of the timing belt. Do not fully tighten it. Otherwise, the timing belt may be damaged. This is an open-frame device and only comes with a small sheet of metal to protect your work surface. XTool also makes a honeycomb work panel specifically for diode lasers that protect your table while also preventing your pieces from becoming charred.Engraving & Cutting Compatibility: Wood, bamboo, cloth, cork, plastic, and more Engraving-specific Compatibility: Fiberglass, stainless steel, titanium alloy, and moreSee tech specs for full list Align the middle plate with the screw holes on the sliders, and use screws to hold the middle plate and sliders together. Before creating your works, you can place the aluminum sheet in the working area of xTool D1 Pro to protect your desk or floor from being smoked or burned. TBF to xTool, many seemingly-insignificant details can impact the actual ability of a laser cutter.
In the example above we have used 20% power and 60 mm/sec speed. Ensure you have the material to be marked under the laser and that the laser is focused properly by using the built in focus tool. Safety is a major concern when operating laser devices. xTool has included a transparent shield attached to the laser module to prevent you from looking directly at the laser beam. You should still wear safety glasses (included) when operating the laser without a cover. The xTool D1 Pro Desktop Laser Engraver is a lightweight, easy-to-use laser engraver with a large engraving area of 430mm x 390mm (16.9x 15.3"), and a light shield keeps users safe and the laser clear of dust or smoke. It's easy to connect with Wi-Fi, USB cable, or a large capacity TF card for offline use and can be equipped with optional risers to engrave taller objects.
Some materials should not be burned with a laser due to their chemical makeup – they could melt, catch fire or produce toxic fumes. Dallas Maker Space has published a list of safe and hazardous materials to use with their laser. The list of no-nos includes plastics, fiberglass and certain foams.
Great Deal 
New Comment