ACO drains are renowned for their durability, reliability and attractive design. Over 50 years of experience in the drainage industry has made ACO drainage one of the best known and respected brands. Their range of A15 load class channel drains is a favourite amongst builders, plumbers, DIYers and landscapers alike thanks to their attractiveness, ease of installation and function. The method of installation is essentially the same, but the placement of the corner pieces will be key. The corner drain has been placed and you are ready to begin marking. Mark with a pencil or sharp marking point where each drain piece will need to be cut to ensure the corner unit fits into place. Step 3: Cutting the drain parts The system is fully certificated, UKCA and CE marked to BS EN 1433:2002 from Load Class A 15 pedestrian areas, up to and including Load Class D 400 suitable for parking of all types of road vehicles*. The patina finish is being seen more and more in high-end garden and landscape projects, with products from planters to walls being offered by a range of manufacturers, the finish can enhance a space and textures felt and seen within it.

If the manufacturer does not provide quad connectors, then you will need to cut where the two pieces will connect on the corner to make one. The corner sections will need to be made with joints so that an angle of 90° can be made. This is the generic term for linear systems that incorporate a channel together with an inlet detail that is embedded in the constructed surface.By removing the internal base of the corner unit you can connect vertically directly onto 110mm diameter PVC-U underground pipe. Firstly, ensure that the current set pieces of drain your additional part will connect to extends past the end of the wall where the line of the channel drain is currently against. If this has been done, place what will be the other part of the corner of the channel drain into the position you want ready for marking. Step 2: The markings There are two main ways to create a corner channel drain. Whether that corner may be a standard “L” shape, “T” shape or any other corner type, you can manufacture the drain to suit specific standards. A quad section can be one of the easier ways to install a corner channel drain. Many ranges already have these available to fit alongside their standard line channel drain parts. Not only can they be placed without the need to cut to a specific size, but come in a wide variety of sizes to suit the channel drain you’re installing. REMINDER: Although this is a basic guide, we recommend you follow manufacturer instructions if provided.

The channel is longer than it is wide with a cross sectional dimension design to contain the flow from the associated surface surrounding the installation. The channel body can bemanufactured from Polymer Concrete, Plastic or Steel. Protective UltraSTEEL galvanised edge rails for improved strength and bonding between channel and surface materials. Also available in stainless steel Where you have marked the first line drain piece, use a cut-off saw, angle grinder or hand-saw to cut off the spare drain length. This will allow the corner unit to be accommodated following the cutting process. Ensure this is accurate and, as with the line of the channel drain, ensure any debris has been removed before installation to reduce the risk of leaks. Step 4: Connecting the parts ACO Threshold drain is a slim plastic and aluminium channel which has been designed for entryways to domestic properties. Its slimline design allows the channel to be discrete and stylish without compromising on function. ACO Threshold will stop water from ponding at the entrance to a home. It’s advised that this ACO channel drain is used at the door threshold but not in the doorway. For drainage at the doorway, to prevent water from coming into the property, use ACO DoorWay drain as detailed below. Following the cutting process, you can now place the connection piece into position and join the units together. This can be done in the same way as you would do a standard channel drain unit. Slide the unit into the clean connection piece and then gently tap it into place using a mallet or similar hammering-type tool.As a guide, 1:100 type fall can be suitable for smooth drainage fittings. Step: 6: Fitting the short end More advanced forms of slot systems like the ACO Qmax although not load bearing in their own right, are formers that facilitate the construction of a ‘non-interrupted’ pavement. Line (or, Linear) drain

ACO channel drainage also comes in a variety of forms from pedestrian class A15 to light traffic roads class C250, domestic driveway channels B125 and a whole lot more! ACO HexDrain is a plastic A15 load class channel drain built from recycled polypropylene for high strength and high durability. Designed with 8 possible outlet positions, this unique A15 channel drain can be used in domestic drainage projects such as along garage thresholds, landscaping projects and a range of DIY garden and patio applications. Both the ACO HexDrain base and grate come in 1m lengths and the base has markings at 500mm for easy cutting and measuring. ACO DoorWay drain slots underneath the doorway at the point of installation meaning that the door frame doesn't need to be cut or altered. The system is suitable for use in a wide range of applications including commercial and residential developments, pedestrian precincts, landscaping and parking areas for all vehicle types. The channel unit is manufactured from Vienite, ACO’s high strength polymer concrete and forms the main component of the system. You want to fit the final part of the corner. As before, measure and cut the length of the channel required to fit against to wall of the property. Before you place the channel itself, fit the end cap to the short section to ensure the channel can be installed into the correct position after.ACO is arguably one of the most widely recognised brands in the design, development and manufacture of surface water drainage systems. Their product durability and reliability places them as firm favourites, admired by architects, specifiers, contractors and DIY enthusiasts alike.

Here Drainage Superstore we are proud to supply their vast range of products and supplies at our famously competitive prices. Their extensive product portfolio offers market leading and high-performance solutions for every drainage application from internal and building drainage, to landscaping, commercial projects, highways, airports and even environmentally sensitive drainage systems.The corner unit is supplied with 4 x solid sides, any of these can be removed to allow rainwater to flow into or through the corner unit. To form a 90° angle you simply cut out the two relevant side sections and clip the HexDrain channel to the corner unit, for a watertight connection please use a suitable sealant.