Joined in 2023 
82 
63 About this deal
Then I added points to make the hole creation process (step 9) easier. I created another sketch on the surface of the extruded rectangle and added two construction lines 8mm from the side and 3mm from the top right. I repeat this step on the bottom left (the 3mm would now be from the bottom left) and made sure they are coincident. There is a picture of this above. The LED lights are very long, so I then cut the end of the lights at the nearest copper part where each section is adjoined. There is a picture of this above. Astronaut Cat on the Moon Resin Lamp Dragon Epoxy Lamp Handmade furniture and decor Bedroom Night Light Lamp Christmas Gift for daughter Using this line, I drew a rectangle to the center hole of the base. The sides should be 62mm and the rectangle should overlap and partly cover the hole.
Sport Car Design Led Lights as a Gift for Him. F1 Table Lamp Car Lover Gifts. Classc Car Night Light Gift for Boyfriend.Personalized Night Light with Moon & Stars - Nursery Decor - Custom Name Light Night Gift - Kids Room Decor - Personalized Gifts for Kids |Astronaut Cat on the Moon Resin Lamp Dragon Epoxy Lamp Handmade furniture and decor Bedroom Night Light Lamp Christmas Gift for daughter I went to Prusaslicer so I could import the new file. I placed the moon on its bottom using the "Place on Face" option on the sidebar. Keep collections to yourself or inspire other shoppers! Keep in mind that anyone can view public collections - they may also appear in recommendations and other places. Decide on a design for the ledge. I wanted mine to be a rectangular box of 37mm by 62mm. I marked my design onto the styrofoam using a pen.
The LED light kit should have an RGB control box with extrusions containing holes. I measured all the dimensions of the control box and the diameter of the holes using the dial calipers. This step is extremely important, measure every part of the control box, especially the extrusions, before purchasing screws. Nursery Wall Light Elephant, Lighting Elephant Balloon, Baby Room Light, Cloud Wall Lamp, Elephant Light With Balloon, Baby Room Decor Birthday Gift for her, gift for him, Anniversary Led Lamp For Couple, Personalized 3D Led Photo Nightstand LightFor my base design, I had a hollow base with a diameter of 6 inches (152.4mm) and walls of 3mm wide. The cylinder in the middle had a diameter of 1.8 inches (45.72), just a little smaller than the hole of the sphere because you will need to wrap your LED lights around this cylinder. The walls of this cylinder were 1mm wide. The space where the cylinder meets the base should be empty since the wires of the LED lights will need to go through the cylinder. Plan for two holes with diameters of 25mm in the walls of the base and the cylinder; the wires of the LED light will go through them. Custom 3D Photo Moon Lamp | Personalized Moon Lamp | Personalized Moon Lamp w/ Photo & Engraved Text | Moon Lamp Night Light As with all things in life, unexpected problems can arise. If the LED lights break or tear, don't throw them away! You can use a soldering kit to fix them by reconnecting the wires to another copper spot. This happened to me too, so don't panic if you have the same issue.
Anime Gifts 3D Led Lamp RGB 16 Colors W/Remote Conrtol, Manga 3D Night Light, Anime Figures ,Anime Christmas Gifts, Anime Birthday gifts Personalized 3D moon lamp - perfect gift with individual picture and saying - 16 colors with dimming functionThe overall structure of the base is done, but I needed to design a raised ledge to keep the LED light's control box in place. Here is where I used the styrofoam wire cutter to test out my design before implementing it. This step is optional, but if you changed any design measurements I highly recommend testing your control box stand. I created another sketch on the top of the base and drew two circles with diameters of 45.72 and 35.72 from the center. These are the circles that will form the cylinder Moon lamps produce a soft and warm glow and many offer a variety of colour settings and light modes, to create a relaxing atmosphere. Custom 3D Photo Moon Lamp w/ Touch+Tap Switch for Family (10-20cm) | Personalized Moon Lamp w/ Photo & Engraved Text | Best Home Decor Gifts
I went through many challenges throughout the process of this SIDE Project, including having to learn how to use software like Fusion from scratch while I was actively working on the creation process and improving on my project many times throughout the year. Then I created a construction line from the center of the hole that leads to the cylinder to the hole in the wall of the base. I drew another 37mm line that is tangent to this line, connecting them to both sides of the circle. Use the coincident tool to make sure they are really attached to the circle. Then I extruded a cylinder from the sketches on the surface of the base. This cylinder should be at most 127mm long. If you had cut off too much of the moon in Meshmixer, make this cylinder even shorter.Personalized Lamp for Psychologist. Psychology Student Graduation Gift. 3D Brain Lamp, Personalized Gift for Neurologist Custom 3D Photo Moon Lamp, Magic 3D Printed Lunar Night, Personalized Moon Lamp, Moon Light, Home Decor, Custom Moon Lamp, Christmas Gift Anime Night Lamp, Christmas Night Light, Anime Led Light, 3D Anime Night Light, Anime Lamp, Manga Gift, Anime Led Lamp, Anime Decor Gift This tutorial uses Lithophane Maker's Globe Maker and a little Fusion 360 design to create a colorful moon that is lit up from the inside with string LED lights. It's perfect as a small lamp or decoration for any person who doesn't want to wait for the nighttime to see the moon. I threaded the light through the hole in the base and up into the interior of the cylinder. The lights should come out of the hole in the side of the cylinder. Then I took off the covering for the double-sided tape and wrapped the LED lights around the cylinder.
Great Deal 
New Comment